©1995 Hamtronics, Inc.; Hilton NY; USA. All rights reserved. Hamtronics is a registered trademark. Revised: 10/23/02
-Page 11-
PARTS LIST FOR R100
RECEIVER, FOR 46-54 MHZ
Ref #
Value
(marking)
C1
82 pf np0
C2
150 pf np0 (151)
C3-C4
.001 uf (102, 1nM, or 1nK)
C5
56 pf np0
C6
1 pf
C7
62 pf np0
C8
1 pf
C9
56 pf np0
C10
6 pf np0
C11
.01 uf (103)
C12
5 pf
C13
6 pf
C14
5 pf
C15
Piston trimmer, 2-11.2 pf
C16
39 pf np0
C17-C18 150 pf (151)
C19
.001 uf (102, 1nM, or 1nK)
C20
82 pf np0
C21
2 pf
C22
82 pf np0
C23
not used
C24
.001 uf (102, 1nM, or 1nK)
C25
82 pf np0
C26
2 pf
C27
82 pf np0
C28
0.47 uf electrolytic
C29
0.15 uf polyester (red)
C30-C31 .001 uf (102, 1nM, or 1nK)
C32-C33 .01 uf (103)
C34
0.15 uf polyester (red)
C35
4.7 uf electrolytic
C36
47 uf electrolytic
C37
0.15 uf polyester (red)
C38
470 uf electrolytic
C39
68 pf np0
C40
220 pf (221)
C41-C43 0.1 uf monolithic (104)
C44
2 pf
CR1-CR2 1N4148 ( p/n may not be
marked)
FL1-FL4
10.7 MHz matched xtal
filter set
FL5
455 kHz ceramic filter,
20 kHz bw (blue)
J1
RCA jack
L1-L4
6½ tunrs (blue)
L5
10.7 MHz IF transformer,
p/n 7A-691F
L6-L9
6½ turns (blue)
L10
455kHz IF transformer
p/n 831-5 or YMC-15002
or T1003
Q1-Q2
N.E.C. 3SK122 or Philips
BF-988 dual-gate mos fet
(
M
static handling pre-
cautions required)
Q3
2N3563 or 2N5770
Q4
not used
Q5
2N3563 or 2N5770
R1-R3
100K
R4-R5
15K
R6
680
Ω
R7
not used
R8
47K
R9
68K
R10
100K panel-mount pot.
R11
68K
R12
100K
R13
47K
R14
330K
R15
680
Ω
R16
4.7K
R17
1.2K
R18
22K
R19
100K
R20
100K panel-mount pot.
R21
47K
R22
3.3
Ω
(orn-orn-gold-gold)
R23
15K
U1
MC-3361P IF Ampl/
Det/Squelch
U2
LM380N-8 Audio Amplifier
U3
78L08 Voltage Regulator
Y1
Channel Crystal (see text)
Y2
10.245 MHz, 62 pf,
parallel-resonant IF xtal
Z1-Z4
Ferrite Beads, double long
à
Note the following
changes for this model:
1. R7 and C23 are not used. Q4 is re-
placed with C44, installed where the
base and collector leads of Q4 would
normally go.
(See detail below.)
2. When tuning the oscillator, a change
in procedure is required because this
frequency scheme does not use a mul-
tiplier stage. L6-L9 are all simply
peaked for maximum signal sensitivity.
Skip alignment procedure step (c). In
step (g), alternately peak all four coils,
L6-L9, for maximum as stated for L8-L9.
Q2
Q3
C27
C26
C10
R3
L9
L5
Z2
Z3
C25
C24
R5
C20
C21
C22
L6
L7
C43
L8
C19
THESE 5 HOLES
C44 INSTALLED
NOT USED
IN PLACE OF Q4
BASE-COLLECTOR
DETAIL OF LEFT-REAR CORNER OF RECEIVER
SHOWING COMPONENT CHANGES FOR THIS MODEL