background image

Here are some suggestions to help you 
maintain your fan. 
1. 

 Because of the fan's natural 

movement, some connections may 
become loose. 

Check the support 

connections, brackets, and blade 
attachments twice a year.

 Make sure 

they are secure. 

(It is not necessary to 

remove fan from ceiling.) 

2.    Clean your fan periodically to help 
maintain its new appearance over the 
years. Do not use water when cleaning. 
Use only a soft brush or lint-free cloth to 
avoid scratching the finish. The plating 
is sealed with a lacquer to minimize 
discoloration or tarnishing. This could 
damage the motor, or the wood or 
possibly cause an electrical shock. 

3.  You can apply a light coat of 
furniture polish to the wood for 
additional protection and enhanced 
beauty. Cover small scratches with a 
light application of shoe polish.   

4.

There is no need to oil your fan. 

The motor has permanently lubricated 
sealed ball bearings. 

WARNING

MAKE SURE THE POWER IS OFF AT THE 
ELECTRICAL PANEL BOX BEFORE YOU 
ATTEMPT ANY REPAIRS. REFER TO THE 
SECTION, "MAKING ELECTRICAL 
CONNECTIONS."

12.Care of Your Fan 

Summary of Contents for Sabitini


















Reviews: