Assembly of the Light Fixture: Option 1 - Hidden wire
□
Find a location on the deck where you want to mount the light.
□
Using the template provided with the instruction manual, place it
over the deck and use a sharp object or a pen to mark where you
are going to put the screws (E) and drill the hole.
□
Drill a 1 in. hole where specified. Use the two (2) provided screws
(E) and screw them in the deck according to the template.
□
Pass the wire (C) and the connector (D) through the hole.
□
Mount the half brick light (B) on the screws (E).
Assembly of the Light Fixture: Option 2 – Flushmount
□
Find a location on the deck where you want to mount the light.
□
Using the template provided with the instruction manual, place it
over the deck and use a sharp object or a pen to mark where you
are going to put the screws (E).
□
Insert the screws (E).
□
Mount the half brick light (B) on the screws (E).
Assembly of the Light Fixture: Option 3 – Flushmount to cover older models
□
Remove the diffuser plate and the light component by unscrewing
the two thumbscrews (B)
□
Pass the wire in the hole
□
Secure the fixture onto the surface, covering the hole from the old
light fixture using the two screws from the old model (not included)
□
Install the diffuser and light component with the two thumbscrews (B)
□
Make sure the O-ring stays on the thumbscrews (B)
Item #1001 492 878
Model #HD38682
Use and Care Guide
LOW VOLTAGE LED HALF BRICK STEP LIGHT
Part
Description
Quantity
A
Thumbscrews
2
B
Half brick light assembly
1
C
Wire
1
D
Connector
1
E
Screws
2
PACKAGE CONTENTS
Assembly and Installation
1
Attaching and installing the light
2
Connecting the wires
WARNING: The wire connector (D) contacts have sharp edges for piercing the
main low voltage cable. To avoid injury, do not touch the metal contacts.
CAUTION: The wire from the low voltage power unit shall be 12-16 AWG type
underground low Energy Circuit Cable or SPT2W.
IMPORTANT:
• Protect the wiring by routing it in close proximity to the light fitting, or next to a
building structure such as a house or deck.
• The landscape wire and connector can also be hidden under stone or buried
under grass at a maximum depth of 6” (15.24 cm).
• Do not submerge fixture in water.
WARNING: Risk of Electric Shock. Install all luminaires 10 ft. (3.05 m) or more
from a pool, spa or fountain.
□
Place the wire connector (D) on opposite sides of the low
voltage cable (not included) where the fixture will be located.
□
Align and fit the main low voltage cable vertically to the slot of
the wire connector (D) as shown.
□
Press the wire connector (D) together until fully seated and
locked around the cable. Pre-set prongs will pierce the cable
insulation and establish contact. Turn on the power unit. If the
light fixture does not turn on, repeat the previous steps.
□
Once the clip-on connector (D) is in place, wrap it with
electrical tape for additional protection.
□
CAUTION BE CAREFUL! THE WIRE STABS ARE VERY SHARP!
□
After all fixtures are installed, turn on the transformer.
D
Only for use with low voltage power units with a maximum output rating of 15V,
300W per secondary.
FOR LANDSCAPE LIGHTING SYSTEMS ONLY. OUTDOOR USE ONLY. THE DEVICE IS
ACCEPTED AS A COMPONENT OF A LANDSCAPE LIGHTING SYSTEM WHERE THE
SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR LOCAL
INSPECTION AUTHORITIES HAVING JURISDICTION.
ETL LISTED UNDER MODEL # U000-1708
Please read and save these instructions
A
B
C
E
D
Option 2
Option 1
Screw (E)
Screw (E)
Wire (C)
Connector (D)
Half brick
light (B)
CAUTION: Safe for outdoor operation
WARNING: Install in accordance with all local codes and ordinances.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Option 3
Thumbscrew (B)
