HAMPTON BAY HB-7612-02 Use And Care Manual Download Page 2

 

2

Table of Contents

Table of Contents .......................................2
Safety Information .....................................2
Warranty ....................................................2

3-Year Limited Warranty ........................2

Pre-Installation ..........................................3

Planning Installation ..............................3
Specifications ........................................3
Tools Required .......................................3
Hardware Included .................................4

Package Contents ..................................4

Installation - Wired Doorbell ......................4
Installation - Wireless Doorbell ..................6
Operation ...................................................7
Tunes .........................................................8
Care and Cleaning .....................................8
Troubleshooting - Wired Doorbell ..............8
Troubleshooting - Wireless Doorbell ..........9

Safety Information

PRECAUTIONS

 

Please read and understand this entire manual 
before attempting to assemble, install, or operate 
this doorbell.

 

All electrical work must be in accordance with 
national and local electrical codes. If in doubt, 
consult a qualified electrician.

 

For wired installations, this doorbell requires 
a 16 volt AC, 10 watt or a 16 volt AC, 15 watt 
transformer.

 

For wireless only installations, this doorbell 
requires 3 “C” alkaline batteries. Do NOT install 
batteries if connecting the doorbell to transformer 
wires.

 

For proper hardwired doorbell operation, a diode 
must be installed on the push button of the main 
entrance.

WARNING:

 To prevent possible SERIOUS INJURY or 

DEATH never allow small children near batteries. If battery 
is swallowed, immediately notify a doctor.

WARNING:

 DO NOT mix old and new batteries. DO 

NOT mix battery types - such as alkaline, heavy duty, and 
rechargeable - in a single device. Battery leakage may occur.

WARNING:

 DO NOT DISPOSE OF BATTERIES IN FIRE. 

BATTERIES MAY EXPLODE OR LEAK.

WARNING:

 This doorbell requires a low voltage electrical 

connection. Do not connect directly to 120V AC.

NOTE:

 The range of the wireless doorbell can vary with 

location, temperature, and battery condition.

This device complies with Part 15 of the FCC Rules and 
RSS-210 of Industry Canada. Operation is subject to the 
following two conditions: (1) this device may not cause 
harmful interference, and (2) this device must accept any 
interference received, including interference that may 
cause undesired operation.
The user is cautioned that changes or modifications 
not expressly approved by the party responsible for 
regulatory compliance could void the user’s authority to 
operate the equipment.

Warranty

3-YEAR LIMITED WARRANTY

WHAT IS COVERED

This product is guaranteed to be free of factory defective parts and workmanship for a period of 3 years from date 
of purchase. Purchase receipt is required for all warranty claims.

WHAT IS NOT COVERED

This warranty does not include expendable items (such as light bulbs, batteries, etc.), repair service, adjustment 
and calibration due to misuse, abuse or negligence. Unauthorized service or modification of the product or of any 
furnished component will void this warranty in its entirety. This warranty does not include reimbursement for 
inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges. This warranty 
is not extended to other equipment and components that a customer uses in conjunction with this product.

Contact the Customer Service Team at 1-844-760-3644 or visit www.hamptonbay.com.

Summary of Contents for HB-7612-02





















Reviews: