manualshive.com logo in svg

HAMPTON BAY H27-NG, Owners & Installation Manual

Share
Download
HAMPTON BAY H27-NG Owners & Installation Manual Download Page 31

Hampton

®

 H27 Direct Vent Freestanding Gas Stove

31

INSTALLATION

CONVERSION KIT #434-969 FROM NG TO LP

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !!

Each Kit contains one LPG 
Conversion Kit and one DC
Sparker Kit.

LPG Conversion Kit Contains:
Qty. Part # 

Description

1 

904-163 

Burner Orifi ce #54

1 

918-590 

Decal "Converted to 

  

LPG"

1 

908-528 

Red "LPG" label

1 904-529 

5/32" 

Allen 

Key

1 910-037 

LPG 

Injector 

  

(Pilot 

Orifi 

ce)

1 918-480 

Instruction 

Sheet

DC Sparker Kit Contains:
Qty. Part # 

Description

1 

820-475   

Bracket DC Sparker

 

1 

820-476   

Bracket DC Sparker

1 

904-153   

Washer #8 External Star

1 

904-330   

Nut 8-32 Hex

1 

904-438   

Plug Nylon 0.750 Hole,

 

 

 

 

Black (for H25 / H27  

 

 

        only)

1 

904-531   

Bushing Split Plastic 

   0.500 

in.

1 

904-543   

Screw 8-32 x 3/4 Pan 

   Head

2 

904-553   

Screw #8 x 1/2 Type 

   "B", 

Black 

Oxide

1 910-073 

  Spark 

Generator 

   Battery 

Holder

1 

910-074   

Spark Generator  

 

   Switch 

C/W 

Wire

1 

910-078   

Battery Size AA  

 

   Energizer 

En91

2 

910-199   

Clip Wire Holder

1 

910-903   

Wire Fan To Power Cord 

   Ground 

30 

in.

Installation of the LPG 
Conversion Kit:

1)

 

Shut off the gas supply.

2)

 

 

a)  Lift off the Cast Top and Cast Front, 

remove the glass front (refer to Glass 
Replacement section in the H25 / 
H27 manual)  and carefully remove 
the logs and lava rock (refer to Log 
Installation section in manual).

 

Pilot assembly is now accessible for 

steps 4) to 9).

     b)  Remove burner by removing the 2 

screws on each side and then lifting 
the burner tray out.

Screws

4)

 

Unscrew the pilot orifi ce with the Allen 
key and replace with the LPG pilot orifi ce 
in the kit and replace pilot cap.

5)

 

Remove burner orifi ce with a 1/2" 
wrench and discard. Use another 
wrench to hold on to the elbow behind

the orifi ce.

Burner Orifi ce

6)

 

Reinstall new burner orifi ce LPG 
stamped #54 and tighten.

Note: Use a magnetic type 

screwdriver if possible.

NOTE: See page 4 for P33-4 conversion instructions and page 7 for E33S / U32S conversion instructions.

3)

  Pull off the pilot cap to expose the pilot

 orifi 

ce.

Summary of Contents for H27-NG

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands