HAMPTON BAY Devereaux II Owner'S Manual Download Page 4

Safety Rules - Read and Save These Instructions

To reduce the risk of electric shock, insure electricity has been turned off 
at the circuit breaker or fuse box before beginning.

All wiring must be in accordance with the National Electrical Code 
“ANSI/NFPA 70-1999” and local electrical codes. Electrical installation 
should be performed by a qualified licensed electrician.

WARNING:

 To reduce the risk of electrical shock or fire, do not use this 

fan with any solid-state fan speed control device. It will permanently 
damage the electronic circuitry.

CAUTION:

 To reduce the risk of personal injury, use only the screws

provided with the outlet box.

The outlet box and support structure must be securely mounted and 
capable of reliably supporting a minimum of 35 pounds, Use only UL 
Listed outlet boxes marked 

“FOR FAN SUPPORT”

.

The fan must be mounted with a minimum of 7 feet clearance from the 
trailing edge of the blades to the floor.

Avoid placing objects in the path of the blades.

To avoid personal injury or damage to the fan and other items, be 
cautious when working around or cleaning the fan.

Do not use water or detergents when cleaning the fan or fan blades. A dry 
dust cloth or lightly dampened cloth will be suitable for most cleaning.

After making electrical connections, spliced conductors should be turned 
upward and pushed carefully up into outlet box. The wires should be 
spread apart with the grounded conductor and the equipment-grounding 
conductor on one side of the outlet box and ungrounded conductor on the 
other side of the outlet box.

All set screws must be checked and retightened where necessary before 
installation.

1

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

WARNING

TO REDUCE THE RISK OF PERSONALL INJURY, DO NOT BEND THE 

BLADE ARMS (ALSO REFERRED TO AS FLANGES), WHEN 

INSTALLING THE BRACKETS, BALANCING THE BLADES OR 

CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS IN– 

BETWEEN ROTATING FAN BLADES.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL 

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE 

FOR FAN SUPPORT WITH THE SCREWS PROVIDED WITH THE 

OUTLET BOX.

ATTENTION

FAN INCLUDES A 190W LIMITER TO COMPLY WITH THE 

DEPARTMENT OF ENERGY 2009 REGULATION.  LAMPING THIS 

PRODUCT OVER 190W WILL CAUSE THIS FAN TO NOT LIGHT.  

PLEASE USE BULBS WITH A TOTAL WATTAGE UNDER THE 190W 

REGULATION.

Summary of Contents for Devereaux II



















Reviews: