HAMPTON BAY 555-219 Instruction Manual Download Page 2

 

2

Thank you for purchasing this Hampton Bay interior track section. This product has been 
manufactured with the highest standards of safety and quality.  
 

FEATURES: 

1.    This 4ft. track section is designed for mounting to ceiling or walls. 
2.

 

All Hampton Bay EC series track adapters and track heads can be installed into the 
track section and can move to any position along the track section.  

 

QUESTIONS, PROBLEMS, MISSING PARTS: 

Before returning to your local Home Depot, please call our Customer Service Team at 1-
877-527-0313 or visit www.homedepot.com. Please reference SKU 675-458, UPC 
008938275088, or SKU 555-219, UPC 008938275002. 
 

IMPORTANT SAFETY INSTRUCTIONS 

When installing or using this track system, basic safety precautions should always be 
followed including the following: 
1.    Read all of these installation instructions before installing the track system.” 
2.

 

Save these instructions and refer to them when additions to or changes in the track 
configuration are made. 

3.

 

Do not install this lighting system in a damp or wet location. 

4.

 

Before energizing make sure that the lighting system is clear of all material which 
could cause a direct short and check all electrical connections to make sure they are 
tight. 

5.

 

Do not install any part of this system (TRACK) less than 7 feet (2.2m) above floor. 

6.

 

Do not install any lamps closer than 6 inches (15.25cm) from any curtain or similar 
combustible material. 

7.

 

For installation with EC series track only. 

8.    This track system is not intended for the use with a power supply cord or convenience 

receptacle adaptor. 

9.    This track system is to be supplied by a single branch 120 volt 60Hz circuit. 
10.    The track is not intended to be pendant mounted such as by a stem or cable. 
11.  The mounting screws are to be mounted along the track in the keyhole slots provided. 
12.  Disconnect electrical power before adding to or changing the configuration of the 

track. 

13.  Do not attempt to energize anything other than lighting track fixtures on the track. To 

reduce the risk of fire and electrical shock, do not attempt to connect power tools, 
extension cords, appliances, and the like to the track. 

Note:

 The important safeguards and instructions appearing in this manual are not meant to 

cover all possible conditions and situations that may occur. It must be understood that 
common sense, caution and care are factors that cannot be built into any product. These 
factors must be supplied by the person(s) caring for, installing and operating the fixture. If 
at any time you are uncomfortable or are unsure of what to do, please contact a qualified 
licensed electrician for further assistance.  

 

SAVE THESE INSTRUCTIONS 

 

TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION (not included): 

 
 

                 

 

 
 
Ladder      Safety goggles    Gloves       Flathead         Phillipshead    Drill    1/4 in or 5/8 in  

                                             screwdriver    screwdriver                      Drill bits                

Summary of Contents for 555-219
















Reviews: