background image

Switch Usage Instruction

CLOSE

AAA

OPEN

 

The gas pressure regulator provided with this appliance must 

be used. This regulator is set for an outlet pressure of 11 inches

water column.

TYPES OF GAS                      PROPANE GAS

Min.Gas supply for input Adj.   25 psi

Maximum Inlet Pressure          250 psi
Manifold Pressure                   11 in.w.c
Gas Rating                               46,000 Btu/hr

OFF/Arrêt

LOW/

Min.

HI/

Max.

ON/ 

Allu-

          mage

OFF/ Arrêt

OFF/Arrêt

LOW/

Min.

HI/

Max.

ON/ 

Allu-

          mage

OFF/ Arrêt

 

 

19
 

HAMPTONBAY.COM

Please contact 1-855-HD-HAMPTON for further assistance.

OPERATION

1

 

     Open the igniter button and install an AAA battery 
     (not included), then secure the cap back on. Before 
     use, make sure that the control knob is in the “OFF” 
     position. Turn the LP cylinder gas valve to fully open
     position. Press down on the control knob and turn 
     counter clockwise to the "LOW" position. Push in the 
     gas control knob all the way and hold. Continue to 
     press the ignition button for 15 seconds.

     If the burner is not lit, press down the control knob 
     and turn clockwise to the "OFF" position. Repeat step 
    1 after 5 minutes. When the burner is lit, press down 
    the control knob and turn it to the desired heat output 
    position between “LOW” and “HIGH”. Press down 
    and turn the control knob clockwise to the "OFF"
    position to shut down the appliance. 
    Turn off the cylinder gas valve.

Lighting

2

Adjusting and Shutting Down

 

To extinguish the flame, push the control knob in and rotate clockwise.

NOTE:

 

Care and Maintenance

 

 

Do not use aerosol polish or any other flammable material to clean the burner while it is in use. 
Inspect and clean the burner regularly. Use a wire-bristle brush to clean the burner surface. A straightened paper clip is useful to remove 
debris or rust from the small burner ports.
Wash frame parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach, acid, or any other solvents on the 
frame parts. 
Inspect and tighten all of the bolts and fasteners on a regular basis to ensure the proper performance and safety of your appliance.

When not in use, we recommend that it be stored in a dry and secure area. Always disconnect the LP gas tank first and store it safely outside. 

  

 
 

The minimum clearance from the sides, rear, and top of unit to adjacent combustible construction: 2' (61 cm) from the sides, 2' (61 cm) from the rear, and 5' 

(152.5 cm) from the top.
Improper lighting operations will cause serious injury and explosion.

 

Caution

Summary of Contents for 1003369084






















Reviews: