background image

Clean:

• Upholstery with mild soap and water.
• Guide rods with a cotton cloth.
• Hand grips with mild soap and water.
• Frame damage can be repaired with touch-up paint can be purchased from your Hammer Strength customer service representative.

Inspect:

•  Cables for wear or damage and proper tension (should not exceed 3/4” deflection.)  Pay close attention at bends and attachment

points.

•  Hardware should be checked for looseness. Tighten as required.
•  Frames should be inspected for wear or damage.
•  Hand Grips should be checked for wear or damage

Lubricate:

• Lube the Guide Rods. Apply the lubricant to a cotton cloth, then run the cotton cloth up and down the guide rods as needed. Do not

spray lubricant directly on the Guide Rods.

PREVENTATIVE MAINTENANCE TIPS

There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:

2. Do not allow minors or children to play on or around this equipment.

1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
    Failure to do so may result in serious injury.

3. Exercise with care to avoid injury.

4. Consult your physician before beginning any exercise program.

15

CAUTION-PLEASE READ

Action

DAILY WEEKLY QUARTERLY BI-ANNUALLY AS NEEDED

CLEAN

Upholstery

X

Guide Rods

X

Hand Grips

X

INSPECT

Visual Overall

X

Cables

X

Hardware

X

Frame

X

Hand Grips

X

LUBRICATE

Guide Rods

X

WARRANTY INFORMATION

CONTACT INFORMATION

10 YEARS

Structural Frame

(Not Coatings)

5 YEARS

Pillow Blocks, Pulleys,

Weight Plates, and Guide Rods

1 YEAR

Belts and Grips

90 DAYS

Upholstery and Any Items

Not Specified

United States, Canada,

Latin America

800.634.8637
847.288.3399

Europe, Africa, Middle East

(+31) 180.646666

Asia Pacific

(+852)2891.6677

United Kingdom

+44(0)1353.666017

VISIT US AT:  

 HAMMERSTRENGTH.COM

Summary of Contents for Hammer Strength OHDMR
















Reviews: