Hamlet HV92USB2 User Manual Download Page 2

Dear Customer, 
thanks for choosing an Hamlet product. Please carefully follow the 
instructions for its use and maintenance and, once this item has 
run its life span, we kindly ask You to dispose of it in an 
environmentally friendly way, by putting it in the separate bins for 
electrical/electronic waste, or to bring it back to your retailer who will collect 
it for free. 
 
We inform You this product is manufactured with materials and components 
in compliance with RoHS Directive 2002/95/CE, WEEE Directive 
2002/96/CE, 2003/108/CE Italian Legislative Decree 2005/151, LVD 
Directive 2006/95/EC and EMC Directive 2004/108/EC for the following 
standards: 
EN 60950-1: 2001 + A11: 2004 
EN 55022: 1998 + A1: 2000 + A2: 2003 
EN 61000-3-2: 2000 + A2: 2005 
EN 61000-3-3: 1995 + A1: 2001 + A2: 2005 
EN 55024: 1998 + A1: 2001 + A2: 2003 
EN 300 386: V.1.3.3: 2005 / AS/NZS CISPR 22: 2004. 
 

 

 
 
The complete CE declaration of conformity of the product can be obtained 
by contacting Hamlet at e-mail address [email protected]
 
The information on the importer for your country are available in the “About 
Us” section of the Hamlet website at www.hamletcom.com. 
 
 

Trademarks and changes 

All trademarks and company names mentioned in this manual are used for 
description purpose only and remain property of their respective owners. 
Hamlet reserves the right to revise this publication and to make changes 
from time to time in the contents hereof without obligation to notify any 
person of such revision or changes. 
 

Summary of Contents for HV92USB2

















Reviews: