Hamilton Beach HBS1200 Quick Start Manual Download Page 13

Troubleshooting Guide

Problem . . . 

Solution . . .

Unit will not run or
stops while it is
running and cannot
be restarted.

• Check to see if unit is securely plugged into an electric outlet.

• Check to see if the fuse for the electric outlet has blown or if a circuit breaker 

has tripped.

• Check to see if the circuit breaker on the back of the unit has tripped.

• Check to make sure that the ON/OFF switch is in the ON (

I

) position.

• Check to make sure that the memory card is installed properly.

Quantity of dispensed
ice is not consistent

• Check to make sure that the unit is level and sitting on a solid, sturdy surface.

Unit is flooding or
water leaking onto
counter

• Make sure that the end of the drain hose is not under water or blocked.

• Make sure that the drain hose is properly installed and routed. See Preparation.

Increased blender
vibration or noise, or
leaking from blender
jar base

• Check blade assembly for loose or damaged blades. Replace if necessary.

13

Caring for the Ice Shaver/Blender

Troubleshooting Guide – Status Messages

Displayed Message. . . 

Solution . . .

• Electric blender motor is too hot. This can be caused when the blender

jar is too full or when blending very thick ingredients. Reduce the
quantity of product in the jar and allow several minutes for the motor 
to cool before blending.

 BLENDER MOTOR

OVERHEAT—TURN OFF 

MAIN POWER SWITCH

• There is a safety interlock on the ice hopper lid. Make sure that the lid

is properly in place.

 

HOPPER LID 

NOT IN PLACE

• The drink size and number of drinks have exceeded 64 ounces (1.9 L).

CONTAINER CAPACITY 

EXCEEDED

• There is a safety interlock on the inner ice hopper. Make sure that the

inner hopper is properly in place.

 

INNER HOPPER

NOT IN PLACE

• There is a sensor on the drain that will indicate if water has backed up

in the drain. Check the drain line for blockages or kinks. 

 

CHECK

DRAIN

• Make sure that the container jar is properly seated on the blender

base. The jar pad sensors prevent the blender motor from starting if
the container jar is not properly seated.

JAR NOT IN PLACE

Summary of Contents for HBS1200


















Reviews: