Halton Safe Management 2.0 Installation, Commissioning, Operating, And Maintenance Manual Download Page 22

Page: 22 / 88

5.3.3 Logging in as Installer

For information on the user levels, see

User levels

1. On the homepage, select the lock icon at the top of the view. A keypad opens.

2. On the keypad, type in password 01473, then select "Accept".

5.3.4 Configuring a Halton Safe HSL link unit

Here you link a Halton Safe HSL link unit to the Halton Safe Management 2.0 controller.

1. Log in as Installer. For instructions, see

Logging in as Installer

2. Select the link unit icon.

Note: The icon is grey if no units have been configured.

3. In the Links view, set the type of each link unit. For more detailed instructions, see

Setting the type of a unit

Value

Description

Not linked to the controller

Link

Linked to the controller

If you get errors when doing the task, see

Troubleshooting

Halton Safe Management 2.0 (SM2) - Installation, commissioning, operating, and maintenance guide

1.0

Summary of Contents for Safe Management 2.0

















































































Search results

Summary of Contents for Safe Management 2.0

Reviews:

Halton Safe Management 2.0, Installation, Commissioning, Operating, And Maintenance Manual, Page: 22 / 88

Search results

Summary of Contents for Safe Management 2.0

Reviews: