OVLEBPFR, OVLSBPFR, OVLSEBPFR
PAGE 2
97811C (Rev. G - 09/17)
OVL - EBPFR/SBPFR/SEBPFR COOLER INSTALLATION
The freeze resistant package must be mounted on an interior wall in a heated area. The room temperature of the interior heated
area must be 50° F (10° C) or higher. The freeze resistant package may be surface or recessed mounted. If recess mounted the
surface of the cover must be flush with the interior wall surface. The package is furnished with screws for mounting the cover to
the box. If the box is recess mounted, do not fasten the top and bottom of the cover to the box. Use the holes on the front only.
1. Fountains using the MPW Mounting Plate refer to Fig's. 7, 8, 9, or 10 for hanger bracket location and rough-in dimensions.
NOTE:
Review separate installation instructions for details of the MPW Mounting Plate.
Fountains using the Wall Plate Assy. refer to Fig's. 1, 2, 3, 4, 5, or 6 for rough-in dimensions.
2. Shown dimensions pertain to installation location (framing must support up to 150 lbs. weight for single fountain and
300 lbs. for dual fountains). These dimensions are required for compliance with ANSI Standard A117.0.
3. Installing back panel.
Ftn. with MPW Mounting Plate: Refer to Fig. 15 for placement of braces onto back panel. Place the upper edge of the panel
above hanger bracket. Slide the panel down until it engages the hanger bracket. Be sure back panel is firmly engaged
before releasing it.
Ftn. with Wall Plate Assy: Place the upper edge of the panel above mounting plate on the wall. Slide the panel down until it
engages the hanger. Be sure back panel is firmly engaged before releasing it.
4. Remove bottom access panel from fountain basin and save the screws.
Ftn. with MPW Mounting Plate: Install the fountain to the back panel and wall using (4) 5/16 “ x 6” long threaded rods,
washers, and nuts (provided). Tighten securely.
Ftn. with Wall Plate Assy: Install the fountain to the back panel and wall using (4) 5/16" x 3/4" long bolts and washers
(provided) thru holes in back panel. A washer is used on the bottom two (2) holes only. Tighten securely.
5. Assemble the operating cable to the fountain bracket. (Fountain should be mounted to exterior wall). The adjustment nuts
should be in the middle of threaded area on the operating cable. See Figure 12. Create a loop in the cable and thread the
free end of the cable through the wall into the freeze resistant box.
6. Connect free end of operating cable to the valve-operating bracket in the freeze resistant box. Remove cable free play by
adjusting the jam nuts on the ends of the operating cable. See Figure 11.
7. Connect water line from fountain bubbler into freeze resistant box. The connection to the box uses a quick connect water
fitting. Position the water line, in the fountain, to drain back into interior mounted box. Any water left standing, in the
exterior line, can freeze. See Fig. 18.
To insert tubing, push tube straight into fitting until it reaches a positive stop. To remove tubing from the fittings, relieve
water pressure, push in on dark gray collar while pulling out on the tubing. See Figure 17.
8. Connect drain and water supply lines to the freeze resistant fountain. Refer to Figure's 1 thru 10 for component positions
Inline strainer must be used on the inlet water line. See Fig. 16.
Start-up
1. Turn on building water supply and check all connections for leaks. Repair as required.
2. Stream height is factory set at 35 PSI. If stream height (See Fig. 19) needs to be changed adjust the regulator in the freeze
resistant package. Clockwise adjustment raises stream height, counter clockwise adjustment will lower stream.
3. Adjust operating cable as required. Cable system should have a minimal amount of free play to allow for proper valve
operation. If the system is too tight the valve will stay in the on position creating constant water flow. Too much free play will
result in non-operation of the valve with the push-buttons.
4. Note: Water from the drain back tube in the freeze resistant package, will continue to run while the valve is actuated.
5. After cable system is adjusted properly stuff flexible insulation into any openings between the outside wall and the interior box.
6. Recheck all connections. If all connections are leak free replace cover(s) on the freeze resistant box(es) and fountain(s).
