HALLDE • User Instructions
4
REMOVAL OF THE CUTTING
TOOLS AND TRAY
Unscrew the decoring device clockwise using
the key and remove the cutting tool, and the
ejector plate together with the tray.
SETTING THE SPEED
CONTROLS
The machine speed control is recommended
as follows:
M = Machine.
GRATER/ SHREDDER
4,5–6 mm: ..........................PF = 2. M = 2.
8–10 mm: ...........................PF = 3. M = 1.
CLEANING
Read all of the instructions before you begin
to clean the machine.
BEFORE CLEANING: Always switch off the
machine and remove the power supply plug
from the socket. Alternatively, if the machine
does not have a plug, turn off the mains switch.
Remove all parts that are to be cleaned.
CLEANING IN A DISHWASHER: All removable
parts can be cleaned in a dishwasher machine.
CLEANING BY HAND: Always use hand
dishwashing liquid. .
CLEANING MATERIALS: Use the brush supp-
lied with the machine or a similar one to clean
the food zones. The knife shaft in the centre
of the machine can be cleaned with a small
bottlebrush. Use a damp cloth to wipe down
the other surfaces on the machine.
DISINFECTION: Use isopropyl alcohol
(65–70%). Isopropyl alcohol is highly inflam
-
mable so use caution when applying it.
WARNING:
• Do not pour or spray water onto the sides
of the machine.
• Do not use boiling or hot water.
• Do not use sharp objects or any objects not
intended for the purpose of cleaning.
• Do not use abrasive detergents or cleaning
products.
AVOID: Do not use cleaning sponges with
scouring pads (e.g. Scotch-Brite™) unless
absolutely necessary.
ADVICE ON CARE:
• Clean the machine immediately after use.
• Dry the machine immediately after cleaning
to avoid oxidation and discoloration of the
surface.
TROUBLE SHOOTING
To eliminate the risk of damage to the motor,
the Cheese Shredder RG400i is fitted with
thermal motor protection that automatically
switches off the machine if the temperature
of the motor should become too high. The
thermal motor protection has automatic reset,
which means that the machine can be started
again when the motor has cooled down, which
usually takes between 10 and 30 minutes.
FAULT: The machine cannot be started or stops
while it is running and cannot be restarted.
REMEDY: Check that the plug is securely fitted
into the power supply socket, or turn off the
mains. Press the starter button. Fit the feed
cylinder and feed attachment according to the
instructions under “Assembling” Check that all
components are correctly fitted and that the
safety arm is raised. Check that the fuses in
the fuse box for the premises have not blown,
and that they have the correct rating. Wait for
a few minutes and try to restart the machine.
If the machine fails to run, call a qualified
service mechanic.
FAULT: Low capacity or poor cutting results.
REMEDY: Make sure that you are using the
correct cutting tool. Fit the decoring device.
Make sure that the speed controlsfor the
machine is in the right position in accor-
dance with the table under the heading
S E T T I N G T H E S P E E D C O N T R O L S .
If necessary, the speed should be adjusted
by a qualified service mechanic. Check that
the grater/shredder plates are in good condi-
tion and are sharp. Press the food down with
less force.
FAULT: The cutting tool cannot be removed.
REMEDY: Always use the ejector plate. Use a
thick leather glove or other glove that the plates
of the grater/shredder cannot cut through, and
turn the cutting tool clockwise to release it.
FAULT: The decoring device cannot be
removed.
REMEDY: Use the wrench to unscrew it
clock wise.
TECHNICAL SPECIFICATION
HALLDE RG-400i
MACHINE: Motor: Two-speed, 1.5/0.9 kW,
208 V, 3-phase, 60 Hz, 230 V, 3-phase, 50 Hz,
400 V, 3-phase, 50 Hz, 415 V, 3-phase, 50 Hz,
with the motor protection set to 3.7 A. Trans-
mission: gear. Safety system: Three safety
switches. Degree of protection: IP45, buttons
IP65. Power supply socket: Earthed, 3-phase,
16 A. Fuse in fuse box for the premises: 10 A,
delayed. Sound level LpA (EN31201): 70 dBA.
CUTTING TOOLS: Diameter: 215 mm. Speed:
400/200 rpm.
NET WEIGHTS: Machine: 54 kg. Cheese Feeder
incl. Manual Push Feeder Cheese: 21 kg.
Cutting tools: About 1 kg on average.
NORMS/STANDARDS: See declaration of
conformity.
Summary of Contents for RG-400i
Page 6: ...7 HALLDE User Instructions...
