background image

Page 

76

 

 

 

SmartFOAM 

DUAL TANK SYSTEM SELECTION 

The following procedures are provided for operation with the 
Hale ADT or MDT II Selectors. 
 

 

CAUTION!

 

UNLESS ENGAGED IN CLASS “B” FOAM OPERATIONS, 
THE HALE SMARTFOAM ADT TOGGLE SWITCH OR 
HALE SMARTFOAM MDT II SELECTOR HANDLE MUST 
B

E IN THE TANK “A” POSITION. IF THE TOGGLE 

SWITCH OR SELECTOR HANDLE IS IN THE FLUSH 
POSITION WHEN THE FOAM PUMP IS STARTED, THE 
FOAM PUMP RUNS FOR ONLY TWENTY (20) SECONDS, 
THEN SHUTS DOWN.

  

 

 

Figure 56

: Dual Tank Selector Operating Positions 

 

Make sure the Hale SmartFOAM is operating and foam 
solution is being discharged (see Figure 56

: Dual Tank 

Selector Operating Positions

). 

 

1.  Set the Hale ADT toggle to the desired TANK, or 

turn the Hale SmartFOAM MDT II handle until the 
indicator points toward the desired TANK. 

2.  When changing toggle switch or selector handle 

position, move smoothly from the TANK 

A” position 

through the FLUSH position to TANK “B” position in 
one motion without stopping. With the fire pump 
discharging water and the Hale SmartFOAM 
operating, a small volume of water is provided to 
separate the two foam types helping to prevent 
possible adverse reactions. 

3. 

After completion of Class “B” foam operations, 
briefly FLUSH the foam pump and return the Hale 
SmartFOAM to the ready condition by returning to 
the T

ANK “A” position and flowing a small amount of 

Class “A” foam concentrate. 

 

IMPORTANT!

 

MAKE SURE THE HALE SMARTFOAM DUAL TANK 
SYSTEM IS IN THE TANK “A” POSITION WHEN 
APPARATUS IS PLACED IN THE READY CONDITION.

  

 
The SmartFOAM controller keeps track of which foam has 
been selected via the selector handle and if that foam has 
been run through the pump (see Figure 57

: SmartFOAM 

Foam in Pump Indicator

).  The small round icon in the bar 

graph indicates what foam is currently in the pump: A, B, or 
CLR. 
 
The SmartFOAM will display a warning message indicating 
that a FLUSH operation must be performed if the operator 
switches from one tank to the other without first FLUSHING.  
The SmartFOAM controller will not allow operation of the 
new tank until a FLUSH operation is performed. 
 

 

Figure 57

: SmartFOAM Foam in Pump Indicator 

Summary of Contents for SmartFOAM 1.7AHP






























































































Reviews: