2
Names of Parts
LED Heater Lamp
Temperature Control Knob
Knob Mount
CAL Pot Plug/
Calibrator
Hex Wrench
Power Switch
Iron Receptacle
Iron Holder Base
Small Cleaning
Sponge
Large Cleaning
Sponge
Cord Assembly
Setting up & Operating the HAKKO 936
CAUTION
The sponge is compressed. It will swell when moistened with water. Before using the until, dampen the sponge with
the water and squeeze it dry. Failure to do so may result in damage to the soldering tip.
A. Iron Holder
1. Small Cleaning Sponge
Dampen the small cleaning sponge with water and
then squeeze it dry. Place it in one of the 4 openings of
the iron holder base.
2. Add water to approximately the level as shown. The
small sponge will absorb water to keep the larger
sponge above it wet at all times.
*The large sponge may be used alone (w/o small
sponge & water).
3. Dampen the large cleaning sponge and place it on the
iron holder base.
Note: The iron receptacles for the 900 (S) and the 907/908
soldering irons are different.
Be sure to use the proper one for each type of
soldering iron. (Refer to Parts List.)
CAUTION
Be sure to turn off the power switch before connecting or disconnecting the soldering iron. Failure to do so may
damage the P.W.B..
B. Connections
1. Connect the cord assembly to the receptacle.
2. Place the soldering iron in the iron holder.
3. Plug the power cord into the power supply. Be sure to
ground the unit.
C. Set the Temperature
1. Set the temperature control knob to the desired
temperature.
2. Lock the knob.
The HAKKO 936 station is equipped with a tempe-
rature control knob lock. After setting the desired
temperature, tighten the hex nut on the underside of
the knob mount using the supplied hex wrench. Turn
the nut clockwise to tighten the knob lock.
CAUTION
• Donʼt over tighten the knob lock.
• Donʼt attempt to turn the knob when the knob lock is on.
Turn clockwise
firmly.
Receptacle
Align the
grooves
and pins
and push
straight in.
English
Cord Assembly
13
1. 將手柄護套
②
從電線方向推移，鬆開栓緊發熱元件的螺絲
①
。
2. 向反時針方向扭開和取出螺帽
③
。
3. 取出焊鐵頭
④
。
4. 向著焊鐵頭方向，從手柄6拉出發熱元件
⑤
和電線。
測試終端板的傳感器和發熱元件的電阻值。此電阻值應與907
和908型一樣。
關於更換程序，請參閱更換部件的使用說明書。
1. 按開焊鐵電源，溫度設定為攝氏480度（華氏896度）。在
焊鐵電線的各個不同部位（包括鬆緊部位）搖動或纏結，
如果發熱器的液晶指示燈閃亮，則應更換電線。
注意：
雖然焊鐵電線正常，當溫度達到攝氏480度（華氏896
度）時，發熱器的液晶指示燈將會閃亮。
2. 測試焊鐵插頭腳和終端板電線之間的電阻值。
腳1-紅色 腳2-藍色 腳3-青色 腳4-白色 腳5-黑色
電阻值應為0歐姆，若大過0歐姆或∞，應更換電線。
請參閱更換部件的圖示。除去燒斷的保險絲，然後再焊接新
的保險絲。
2. 焊鐵電線破損
測試焊鐵電線有以下兩個方法:
3. 更換保險絲
規格
電路圖
名稱
HAKKO 936
耗電
60瓦特
控制臺
936電焊臺/936電焊臺ESD
輸出電壓
交流電24伏特
溫度範圍
攝氏200-480度/華氏392-896度
外形體積
寬120x 高93x 深170毫米 /
4.7x3.7x6.7英寸
重量（不包括電線） 1,300克（2.9磅）
焊鐵頭溫度是以HAKKO 191溫度計測量。
上述規格和設計可能變更，恕不另行奉告。
焊鐵
900S
900S-ESD
907
907-ESD
908
908-ESD
耗電
交流電24伏特-50瓦特
焊鐵頭至接地電阻 低於2歐姆
焊鐵頭至接地電勢 低於2豪伏（標準為0.6豪伏）
發熱元件t
陶瓷發熱器
電線裝置
1.2米 (4英尺)
長度（無電線)
176毫米 (7英寸) 190毫米 (7.5英寸) 200毫米 (7.9英寸)
重量（無電線)
25克 (0.061磅) 44克 (0.09磅)
554克 (0.12磅)
變壓器
3蕊電線
接地
印刷電路板
中 文
