Just press TIMER button several times until TIMER mode disappears.
OFF
ON
OFF
ON
OFF
Used to select Auxiliary electric heater.
2
RESET
LOCK
SLEEP
FAN
TEMP
ON
OFF
SWING
MODE
CLOCK
CODE
LIGHT
Battery loading
Batteries are fitted as follows:
Loading the battery
Ensure that batteries are correctly placed in the compartment
as required for positive and negative terminals.
Replacing the battery compartment lid
The battery compartment lid is reinstalled in the reverse
sequence.
Display review
Press the button to see if batteries are properly fitted. If no
display appears, refit the batteries.
Remove the battery compartment lid
Slightly press and disengage the battery compartment lid marked
with
" "
and then hold the remote controller by the upper
section and then remove the battery compartment lid by pressing
in the direction of the arrow as shown in the figure above.
Note:
It is recommended that the batteries be removed from the
compartment if the remote controller is not used for an extended
period.
The remote controller is programmed for automatic test of
operation mode after the batteries are replaced. When the test
is conducted, all icons will appear on the screen and then
disappear if the batteries are properly fitted.
When the display become weak, this display no power
in the battery, please change the battery.
Caution:
If the remote controller does not operate as designed after
fitting new batteries of the same
type, press the Reset button (marked ) with a pointed article.
+ -
- +
RESET
LOCK
SLEEP
MODE
CLOCK
CODE
LIGHT
A
U
T
O
A
U
T
O
7
blank
ON
Operation mode will be displayed on LCD.
Power indicator lights up.
Every time the button is pressed, display changes as
follows:
Select .
(3)Time setting for TIMER ON
Press TIME button.
(5)Time setting for TIMER OFF
To cancel TIMER mode
Every time the button is pressed, time increases 10min.
If button is kept depressed, time will change quickly.
Every time the button is pressed, time decreases 10min.
If button is kept depressed, time will change quickly.
Time will be shown on LCD.
It can be adjusted within 24hours.
AM refers to morning and PM to afternoon.
Time displayed: Unit starts at Xhour X min.
After time setting, press TIMER button to
confirm."ON" stops blinking, While "OFF"
starts blinking.
(4) Time confirming for TIMER
Follow the same procedures in "Time setting
for TIMER ON".
(6)Time confirming for TIMER OFF
After time setting, press SET button to confirm
"OFF" stops flashing.
Time displayed: Unit stops at X hour X min.
According to the Time setting sequence of TIMER ON or TIMER OFF, either Start-Stop or Stop-Start
can be achieved.
(1)After unit start, select your desired operation mode
(2) Press TIMER button to change TIMER mode
ON
OFF
Operation
The function of code A:TIMER ON/OFF
FRESH
HIGH/SO
TIMER
SET
FILTER
A
HEALTH
1
HEAT
*
MODE
FAN
HEALTH
TEMP
CLOCK
SET
TIMER
SLEEP
RESET
FILTER RESET
ON/OFF
PM
AM
1
SET
SWING
HEAT
6
3
2
4
5
4
Parts and Functions
When operating the remote controller in an area where
electronically controlled lights are installed or wireless handsets
are used, please move closer to the indoor unit as the function
of the remote controller might be affected by signals emitted by
the above mentioned equipments.
Battery loading
Confirmation indicator
If no indication is displayed after press ON/OFF button,
reload the batteries.
Remote Controller Operation
When in use, direct signal transmission head to
the receiver placed on the indoor unit
The distance between the remote controller and the receiver
should be max 7m and there should be no obstacle between them.
Do not throw the remote controller; prevent it from being damaged.
Clock Set
When unit is started for the first time and after replacing batteries in remote controller, clock should
be adjusted as follows:
1.Press CLOCK button, clock indication of " AM " or " PM " flashes.
2.Press or to set correct time. Each press will increase or decrease 1 min. If the button is kept
pressed, time will increase or decrease quickly.
3.After time setting is confirmed, press "SET" : AM or PM stop flashing, while clock starts working.
Note:AM means morning and PM means afternoon.
FRESH
HIGH/SO
TIMER
SET
FILTER
HEALTH
HEAT
16.FRESH Button
Used to set fresh mode, the unit will draw in fresh air.
Displays when healthy run function is set.
22.TEMPERATURE Display
34.LOCK State Display
33.BATTERY Energy Display
Notify the user when it is time to change the batteries.
24.HIGN/SO Run Display
26.SIGNAL SENDING Display
28.Fresh Display
29.Auxiliary ELECTRICAL HEATING Display
30.HEALTH Display
32.SLEEP State Display(
In function of code A)
31.Operation MODE Display
35.FAN SPEED Display
23.AUTO SWING Display
20.TIMER Display
21.FILTER Display
36.TIMER ON Display
17.SLEEP Button(In function of code A)
(The clock must be corrected before setting sleep function)
Used to set sleep mode.
18.FAN Button
Used to select fan speed:LOW,MID,HIGH,AUTO.
19.TIMER OFF Display
When the filter need be cleaned, the sign will
appear automatically.
25.Code A display
27.Code B display
The function of code A
The function of code B
LOW
MID
HIGH
AUTO
LOW
MID
HIGH
AUTO
37.HEAT Button
1
4
5
6
3
2
3
