The ventilation
holes at thebottom
Before Using
Before Using
Safety precautions
In case the washing machine is installed on ground
with carpet, be careful not to block the ventilation hole
with carpet.
Do not put the machine at damp place like the
bathroom. Never wash it with water. Do not
put wet laundries on the control panel coating
.
Do not let the machine share one receptacle with other
electric appliances. If the power plug is damaged, or
the plugging into the receptacle is loose, do not use
the plug any more.
Do not wash water-proof laundry like the raincoat,
bikecovers, down textiles etc. To avoid abnormal
vibrations in spinning and damages to the laundries.
Do not bend, stretch, twist, bind the power cord by force, or reformit.
Do not press or clamp it with heavy items. If the power cord and power
plug are bad, or the receptacle is loose, be sure to have it replaced by
the technicians of our special shop or our agent,or the after-sales service
department to avoid any risk.Keep the prong of the power plug clean.If
dust is found on the power plug, please wipe it off with dry cloth.
In normal usage of the washing machine, the power
plug shall be ready to be pulled or plugged with hang.
Be sure to pull the plug off and close the water faucet
when occurring power failure,delivering the maching,
setting the machine idle or cleaning the machine,Do
not plug or pull the power plug with wet hand.
earth
Do not use water with temperature higher than 50
Please plug the plug on special 220V AC receptacle.
Be sure to use three phase power receptacle.Ensure
the earthing prong of the power redeptacle is earth-
ed reliably.Use leakage protector if possible.
The digitron displays E0.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
The water filling does not work, or is
slow. After about 15 minutes later,
the digital displays E4.
The drainage cannot work, or is too slow.
The digitron displays E1.
It stops running in midway. The digitron
displays E2.
The power voltage is too low.
The top lid is not closed.
The top lid is opened during reserve
procedure.
Close the top lid.
Close the top lid.
Is the drain hose put down?
Is the drain hose blocked?
Put down the drain hose. Open and close the
top lid once.
Clean the foreign material. Open and close
The top Lid Once.
Are the laundries put slantingly?
Is the machine slanting?
Reorder the laundries. Close the top lid.
The machine will start running after 10
seconds of being placed horizontally.
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the start/Pausebutton once.
Push the sStart/Pause button once
.
The water level sensor is bad.
Please contact the after-sales
service department.
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
Is the screw of the jointer of water
inlet hose loose or awry?
Pull off the power plug. Wait for the
voltage resuming normal before usage.
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Fasten the screw of the jointer properly.
The water tap leaks
The digitron displays E8.
The digitron displays E6.
There's abnormal sound
inside the machine
Phenomenan The reason How to settle
Trouble-shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special
maintenance department or after-sale service department of our company. Do not repair it by yourself.
The digitron displays E9.
The power voltage is too high.
The machine does
not act
Not wash
Not spin
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Common phenomena
Phenomena
Explanation
* The spinning is intermittent when it starts.
* Balance the laundries to avoid slanting.
* The wash proced ure pauses.
* The cloth sensor is detecting the cloth. It will start
adding water after about 48 seconds.
* Select “ Spin” program, but it doesn’t work.
* The program is setting the drain time. A certain
period is needed before it starts spinning.
* The pusaltor pauses during washing, rinsing
or adding water.
* It is to avoid splashing during water filling.
* There may be some water flowing out of the
drain hose in the first use of the machine.
* It is the water remained in the performance
inspection by the factory.