manualshive.com logo in svg

Haier XPB10-LAP, Service Manual, Page: 9 / 15

Share
Download
Haier XPB10-LAP Service Manual Download Page 9

Spin tub shaft 

Bearing seat

Figure 8

Oilite bearing

Inner lining of 
the bearing seat

Fastening screw

Fastening screw of 
the brake wheel

Inner lining of the 
brake wheel

Brake wheel 

Spin motor shaft

Points of Attention in After-sales Service

 

Be sure to switch off the power during dismantling or repair.
Be sure  to use  insulated  wiring  terminals  and insulation  box  in connection of the wires, and 

crimp and fix to proper position with suitable tools.

In  welding connections with electric iron, be sure to twist the wires before welding, and insulate

 with insulation tapes.

In  welding the wires  with electric iron, be sure not to touch  the resin part and insulation part of

 each switch.

The inlay connection wires and terminals shall not be loose or drop.
Do not  make  the wires  touch  the moving parts like the belt, pulley of the motor, brake bar etc. 

Do not make the wires touch the sharp edges and high-temperature area.

In  case  that  there  are metal parts with the wires, do not make the wires touch the metal parts. 

Insulation materials are needed between them.

After assembly, the  washing  machine shall act normally. Check if  it leaks and if the sound and

 vibration are normal.

Dismantling and installation of the control panel component

Loosen the fastening screws. Pull towards the direction
indicated in the figure to dismantle the control panel. In
installation the beard shall lock into the installation hole
of the major frame. (Figure 6)

Dismantling and installation of the spin tub 
frame component

Push  the points marked  with "

" as  indicated in

the  figure  and  pull  the  spin  tub  frame  towards 
upper left direction to dismantle the spin tub frame
components.  In installation, after set  the rear side
of  the spin tub  frame to proper position,  push the
four  points marked  with "

"  downwards by force 

to resume its original position. (Figure 7)

Dismantling  and  installation of
the spin tub

Dismantle  the spin tub  frame component. 
Loosen the fastening screw of the spin tub 
shaft. The spin tub  then can be taken out.
In installation, be sure to inlay the bulge of
the inner lining of  the brake wheel into the
groove of the spin tub shaft. (Figure 8

Figure 6

Spin tub frame 

Dismantle

Installation

Figure 7

INSTALLATION AND ACCESSORY PARTS

8

Model:XPB10-LAP

Summary of Contents for XPB10-LAP
















Reviews:

No comments