.9.
.10.
Cleaning and Special Maintenance
Filter Assembly
For best performance and results, the filter assembly must be
cleaned.
The filter efficiently removes food particles from the wash water,
allowing it to be recirculated during the cycle.For this reason ,it is
a good idea to remove the larger food particles trapped in the
filter after each wash cycle by rinsing the"A"semi-circular filter
and cup under running water.To remove the filter assembly,pull
on the cup handle in the upward direction. The entire filter as-
sembly (made up of the "A" semicircular filter and the"B" fine
filter)should be cleaned at ;east once a month.To clean the filter
and the fine filter,use a cleaning brush .Then,reassemble the fil-
ter parts as shown in the figures below and reinsert the entire
aseembly in the dishwasher,positioning in its seat and pressing
downward.
The dishwasher must never be used without the filters.Improper
replacement of the filters may reduce level of the appliance and
damage dishes and utensils.
Cleaning the Spray Arms
It may happen that food particle become encrusted on the sprayer
arms and block the hole (see "Close up view [interior]",letters C-
F ).Check the sprayer arms periodically and clean them when
needed.
It may occur that the dishwasher does not function or dows not
function properly.Before calling for assistance,Iet us see what
can be done first:have you forgot to press one of the buttons or
to perfom an essential operation?
The Dishwasher Does Not Start
Have you checked whether:
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF swith is on "ON";
- the water supply is turned on.
A
B
Installation
Positioning the Appliance
Positioning the appliance in the desired location.The back should
rest against the wall behind it,and the sides,along the adjacent
cabinets or wall.The dishwasher is equipped with water supply
and drain hoses that can be positioned to the right or the left to
facilitate proper installation.
Levelling the Appliance
Once the appliance is positioned,adjust the feet (screwing them
in or out) to adjust the dishwasher,making it level.In any case,
the appliance should not be inclined more than 2
.If the appli-
ance is level,it will help ensure proper performance.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4(gas)con-
nector and make sure that it is fastened tightly in place (see
figure1).
If the water pipes are new or have not been used for an extended
period of time,let the water run to make sure that the water is
clear and free of impurities.If this precaution is not taken,there is
a risk that the water inlet can get blocked and damage the
appliance.
The connection must be made to the hot water line following the
same procedures as those for the connection to the cold water
line.
Anti-Flooding Protection
The dishwasher is equipped with a system that stops the supply of
water in the event of a problem with the water supply hose,or leaks
within the unit,in order to prevent damage to your home.If for any
reason the box containing the electrical components happens to
get damaged,remove the plug for the appliance from the socket
immediately.In order to guarantee that the anti-flooding feature
operates properly,the"A"box with water supply hose must be at-
tached to the water supply tap as shown in Fig .1.No other type of
connection is acceptable.The water supply hose must not,under
any circumstances,be cut,as it contains electrical parts which are
live.If the length of the hose is not adequate to make a proper
connection,the hose must be replaced with one whith is long
enough.This hose is available upon request from specialised re-
tailers and service centres.
Drain Hose Connection
Insert the drain hose into a drain pipe with a minimum diameter
of 4cm,Or let it run into the sink,making sure to avoid bending
or crimping it.Use the speical plastic support that comes with
the appliance (see figure fig.2).The free end of the hose must
be at a height between 40 and 100 cm and must not be im-
mersed in water.
Attention:
The special plastic hose support must be solidly fastened to the
wall to prevent the drain hose from moving and allowing water to
spill outside the drain.
Electrical Connection
After making sure that the voltage and frdquency values for the
current in the home correspond to those on the rating plate
(located on the staunless steel inner door of the appliance) and
that the electrical system is sizedd for the maximum voltage on
the rating plate,insert the plug into an electrical socket which is
earthed properly (the earthing of the appliance is a safety re-
quirement mandated by law).
If the electrical socket to which the appliance must be connected
is not appropriate for the plug,replace the plug ,rather than us-
ing adpators or the like as they could cause overheating and
burns.
Installation
Hot Water Connection
The water supply to the appliance can also be connected to the
house's hot water line (centralised system,heating system),as
long as it does not exceed a temperature of 60
.
In this case,the wash cycle time will be shortened by about 15
minutes and the wash efficiency slightly reduced.
fig.2
GB
GB
The Dishwasher Does Not Load Water
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house on and has sufficient pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishes Are Not Clean
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house on and has sufficient pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishwasher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.
If,despiste all these checks,the dishwasher still does not function
and/or the problem persists,contact the nearest authorised service
centre and provide them with the following information:
- the nature of the problem;
- the model type number (Mod...)and the serial number (S/N...),
which are indicated on the plate located on the side of the inner
part of the door.
Never call on unauthorised technicians and refuse to al-
low parts to be installed that are not original spare parts.
Troubleshooting
fig.1
