background image

Control Panel Illustration

Mode

Power

On/Off

HEATING

KEEPING

SET

ACTUAL

1. Set Button    
2. Temperature and Clock Time Increase Button
3. Temperature and Clock Time Decrease Button
4. Real-time Heating Indication
5. Medium Warm Indication  
6. Night Power Indication   
7. Heating Power Indication Area
8. Heating Indication
9. Delay Indication 

10. Intelligent Indication
11. Mode Button 
12. Power Level Selection Button
13. On/Off Button 
14. Warm Keeping Indication
15. 

 2 Indication

16. Clock Time Display 
17. Temp.Setting / Actual Temp Display
18. 

 1 Indication    

Time

Time

Signaling Indication

Real-time Heating Indication

Medium Warm Indication

Night Power Indication

Intelligent Indication

Delay Indication

Mode

Power

Confirm

Set

850 W

1300 W

2150 W

TIME 1

TIME 2

Remote Controller Panel Illustration

For the first use after installation, due to there's no water within the tank, first the city water 
inlet valve and mixing valve must be opened. Close the mixing valve when water flows out 
continuously from the showerhead or other outlets (the tank is full). Check connections 
are free of water leakage, and insert the power plug. 
1. Powering On
    This product has a power failure memory function, i.e. it remembers temperature setting, 
power level, clock and current working status. Upon connecting power, all indications on 
the display are displayed for 2 s before the system goes into standby status (with only 
clock display and all buttons except On/Off button inactive) or previous working status 
before power failure with corresponding indicators lighted on. For example, machine as 
shown in Fig. 6 is in standby status with only On/Off button active.

Operation Instructions

Installation

Installation must be made by installers of or designated by our company after-service 
department. The water heatershall be wall-mounted.
Before installation, make sure water heater rear wires are fit firmly. Determine an 
installation location. Make four holes

12mm, 65 mm deep in the wall with an impact 

drill as shown in Fig. 2. Insert and fixexpansion hooks and expansion bolts in 
corresponding wall holes. Lift the water heater. Insert wall rack onto the hooks and bolts. 
Fit flat washers, rear wires and nuts in turn onto the bolts (see Fig. 3). Tighten the nuts 
and check them firm. Install accessories such as safety valve, drain hose as shown in 
Fig. 4. Use sealing compound to prevent water leakage.

(Fig.2)

L1

L2

(Fig.3)

To facilitate installation and removal, it is suggested a G 1/2" movable nut is fitted at 
appropriate locations on inlet and outlet pipes respectively. Find water supply location. 
Connect inlet pipe, outlet pipe and city water pipe respectively to the use point. Fill the 
tank full of water and check if water circuit shows any leakage. For any leakage, re-
connection shall be made.

Cold water inlet

Hot
water
outlet

Safety valve

Mixing valve

Showerhead

Connect to drain hose

(Fig.4)

(Fig.5)

Note: Make sure the wall rack is reliably hung on the hooks before releasing your hands. 
Otherwise, the water heater may fall and cause human injury or property loss.

Capacity

50L

60L

80L 100L

L1

L2

320mm 320mm 320mm

320mm

230mm 300mm 282mm 370mm

Connection and Use of Safety Valve:
The safety valve should be connected to the cold water inlet pipe. Please check 
carefully if the direction is correct after installation. The correct direction of installation 
is that the arrowhead on the safety valve should be pointed to the water heater.
Please connect the drain hose to the safety valve. Connect one end of the hose to the 
safety valve vent and the other end to the sewage drain. The hose can be cut short or 
extended as necessary. The hose shall be installed as inclined downward.
The water may drip from the discharge pipe of the pressure relied device and that this 
pipe must be installed in a continuously downward direction and in a frost-free 
environment. Check safety valve once a month as follow: move the small handle of 
safety valve, if there's water flowing out, safety valve is normal; if there's no water flow, 
please contact local after-sales service station.
The pressure relief device is to be operated regularly to remove lime deposits and to 
verify that it is not blocked.

1. Indication Area

2. Mode selection Button 

3. 

4. Set Button

5. 

6. On/Off Button  

7. Confirmation  Button    

8. 

Temperature and Clock Time

    Increase Button   

Temperature and Clock Time

    Decrease Button

Power Level Selection Button

Summary of Contents for SILVER SEA-OX FCD-JTHMG100- E









Reviews: