Haier LMD1841B0 Service Manual Download Page 5

Chapter 4: safety precondition

Please insert the power cord into 

special receptacle with rated vol-

tage. Be sure to use single-phase

 three pins  receptacle. The earthing

 terminal of the receptacle must be

 earthed reliably. If possible, please 

adopt electric leakage protector.

When the machine is normally

using, please put  the power plug

at the location easily to be insert-

ed and extracted by hand. Be sure

to pull the plug off when there's

power failure, or the machine is 

being moved, cleaned or when it 

is idle.

If  the power cord is bad, to avoid risk it is required to replace it by the 

technicians of our special shop or the after-sale service department. 

Keep the pin of the power plug clean.

4

Do  not  put  the  machine  at  damp

place like  the  bathroom .  Never

wash  it   with water. Do not place 

wet laundries on the control panel.

Do not use water hotter than 50 C .

In case the washing  machine is  installed

on  ground  with  carpet ,  do not block the 

ventilation  hole  with  carpet.

Ventilation hole at

the bottom of the

washing machine

Do not wash water-proof laundries like

the raincoat,  bike  covers etc. to avoid 

abnormal vibrations  in spinning.

Do not let the machine share one receptacle

with  other electric  appliances. If  the  power

plug  is  damaged,  or  the  plugging  into the

receptacle  is loose, do not use the plug any

more.

Warning sign

Forbidding sign

Contents marked with that symbol are  actions forbidden  to perform.
Performing of  those actions  may result  in damage of  the machine
or  injure the  personal  safety  of the user.

Contents marked with that symbol are related to the safety of the
product and the users.Please operate in strict conformity to the contents.

Service  Manual

Issue

Rev.

  LMD1841B0

LMD1842B0

Summary of Contents for LMD1841B0




















Reviews: