background image

 

 

 

Service Manual 

Model No.: LE22S600 

 

 

 

12. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 

 

13. Use only an anti-static type solder removal device. Some solder removal devices not 

classi

fied as "anti

-static" can generate electrical charges suf

ficient to damage ES devices.

 

 

14. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to 

damage ES devices. 

 

15. Do not remove a replacement ES device from its protective package until immediately 

before you are ready to install it. 

(Most replacement ES devices are packaged with leads electrically shorted together by 

conductive foam, aluminum foil or comparable conductive material). 

 

16. Immediately before removing the protective material from the leads of a replacement ES 

device, touch the protective material to the chassis or circuit assembly into which the device will 

be installed. 

 

CAUTION:

 Be sure no power is applied to the chassis or circuit, and observe all other safety 

precautions. 

 

17. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise 

harmless motion such as the brushing together of your clothes fabric or the lifting of your foot 

from a carpeted 

floor can generate static electricity sufficient to damage an ES device.)

 

 

1-3-7. Ordering Spare Parts 

 

Please include the following informations when you order parts. (Particularly the Version letter) 

 

1. Model number, serial number and software version 
The model number and serial number can be found on the back cover of each product. Software 

version can be found in the Spare Parts List. 

 

2. Spare part No. and description 
Spare part No. and description can be found in the Spare Parts List. 

 

1-3-8. Photo used in this manual 

 

The illustration and photos used in this Service Manual may not base on the final design of 

products, which may differ from your products in some way. 

 

1-4. How to Read this Service Manual 

 

Using icons 

Icons are used to attract the attention of the reader to speci

fic information. The meaning of each

 

icon is described in the table below: 

 

Note: 
A “note” provides information that is not indispensable, but may nevertheless be 

valuable to the reader, such as tips and tricks. 

 

 

 

6

Summary of Contents for LE22S600


















































Reviews: