Haier IT9002 Service Manual Download Page 12

Care and Maintenance

 

 

 
 

IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF THE COOKER 
HOOD WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY.

 

 

Cleaning

 

 

You should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) 

will scratch the surface and could erase the control panel markings.

 

 

You can clean your cooker hood effectively by simply using a dilute 

solution of water and mild detergent and then dry it with a clean cloth.

 

 

Cleaning the grease filter

 

 

The grease filter should be kept clean to minimise the risk of fire.

 

 

At least once a month you should remove and clean the grease 

filter with hot soapy water. You can also wash the grease filter in a 

dishwasher, ensuring that you place it in an upright position to 

prevent damage from other items in the dishwasher.

 

 

To remove the grease filter, push in the button on the handle and 

then pull down on the filter at the front as shown in Fig. 14.1.

 

 

After rinsing and drying the filter, replace it as shown in Fig. 14.2.

 

 

Please note:

 

 

Cleaning the grease filter in the dishwasher may lead to discoloration. 

This is normal and does not constitute a fault with the appliance.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 

10

 

11

 

Summary of Contents for IT9002




















Reviews: