background image

XBKXSH140113.01 

              BUILT-IN OVEN SALES SERVICE             

 

  9 

 

  12 

 

                   

 

 

6

Part change

 

        Disassembly of back cover 
        WARNING: Turn off the electrical power supply to the appliance prior to servicing it. 
Failure to disconnect the power supply during service may result in an electrical shock 
or fire hazard.   
        Step 1: Disassemble the control panel cover and control panel back cover . 

                             

 

 

 

 

        Step 2: Use a screwdriver to disassemble the screws on back cover, and take the 
back cover out from the clipping hole. 

 

 

 

        Step  3:  Disconnect  the  wires  from  the  turbo  heating  element.  For  the  sake  of 
reassembly  convenience,  please  mark  the  connection  positions  before  moving  the 
wires.    Remove the screws on the turbo heating element, and then take it out of from 
clipping hole.

 

 

 

 

 

        Step  4:  Use  a  spanner  or  a  nut-driver  to  rotate  the  nut  on  the  convection  motor 
clockwise so that the nut be taking out, and then take the fan blade and washer out of 
the convection motor. 

Summary of Contents for HWO60S4MX1













Reviews: