Haier HWM88-0566T User Manual Download Page 5

Disposal after washing 

Safety precautions

Do not put hand into the rotating tub. It is dangerous
even if the rotation speed is slow.  Take special care of 
the  children.  Keep  children  away  from  the  washing
machine  to avoid them climbing on.

    Do not decompose, repair or alter the machine by
    yourself.

   Do not put any hot or heavy items (such as the 
   kettle with hot water) on the washing machine.

 Do not wash laundries with volatile materials
 (such as thinner, petrol etc.).

 Keep the machine away from direct sunlight and
 heat source like the heater.

Benzene

Petrol

The handicapped or children without care shall not use
the machine.

After using, please clean the lint and foreign materials of the lint filter etc. in time. 
Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.

Clean the detergent box and set it on
the control panel seat.

1.The method of dismantle: Push it up aslant and gently.

2.The method of install : install it upwards and aslant

         and push it in .

Dismantle

Install

The filter screen of the water inlet valve is likely to be
blocked  by foreign materials and influence the water
inlet.
Please clean it with brush every two months.

If the cabinet is dirty, wipe it with wet cloth
     Do not flush it directly with water.
     Wipe it with neutral detergent.
     Do not wipe it with thinner, petrol, alcohol etc.

Lint filter:

The lint filter must be used during washing.

It must be cleaned in time after each using.

Figure 1 

Figure 2

Down

Dismantle

Install

 The back cover of lint filter

Install

Dismantle

Down

Up

Up

 The front cover of lint filter

1.Push down the spring piece of the top lint filter to
   make the claws out of the filter cover, and then
   pull out the lint filter to get it down. figure1
2.Pull the back of the lint filter, and then you can get
   down it off the front cover of the lint filter. figure2
3.Sweep the rubbish in the lint filter.
4.Put the back of the lint filter into the front cover .
5.Put the lint filter into filter cover, and make it tight .
6.Make sure the lint filter well installed, or it can
   influence your use.

1.After washing, close the water faucet.  ( If needed, you can dismantle the water inlet hose).

5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time
(about 1 hour), then close the top lid.

4.Hang up the power cord and drain hose.

3.Be sure to pull off the power plug before maintenance.

2.Do not store water in the washing machine for a long period.  Drain  the  water  completely after each using.

Benzene

Petrol

 Please  keep the lint filter in good  condition, and 
install it  to proper position  during washing.  If  the
lint filter is lost or damaged, please contact the local
customer care agent.

To  protect  your  laundries  and washing  machine,
please take out all of the coins, buttons, sand,
hairpin and other foreign materials before washing.

   Please check if the water faucet is open, and if the
   connection of the water inlet pipe is proper.
   It is suggested to use foamless washing powder.

Dismantle

Install

Dismantle

Install

 The cover of lint filter 

  lint filter 

 The back cover of lint filter 

  lint filter 

Summary of Contents for HWM88-0566T











Reviews: