Haier HWM80-27S Service Manual Download Page 10 | Manualshive

Page: 10 / 18

Haier HWM80-27S Service Manual Download Page 10

Adjust the tension of the belt

Loosen the fastening screw at the back of the

base frame. Move the shift fixing gasket along
the direction indicated in the figure to adjust
the tension of the belt. After adjusting, fasten
the screw. (Figure11)

Dismantling and installation of the base frame

Dismantle the back cover. Loosen the wires. Loosen the
fastening screw of the spin tub shaft. Separate the shaft
from the brake wheel. Loosen the brake hook. Take off
the brake cable frame from the installation groove of the
twin-tub. Take off the V-belt. Take out the drain hose from
the groove of the base frame. Loosen the fastening screw
between the base frame and the cabinet to dismantle the
base frame component.

Dismantling and installation of the bearing seat

Once the bearing seat is taken off, it can not be utilized again. Therefore do not dismantle
it as far as possible. In case that it has to be replaced, please dismantle it as per following
sequence, then install a new bearing seat.

Dismantle the spin tub as page 9. Then pull out the bearing seat.
Cut off the inner lining claw inside the bearing seat with cutting pliers and take it out.
Install the new bearing seat and inner lining.
The bearing seat is an inlay component. Be sure to aim the claw of the inner lining at the

hole of the tub then push it in. Please use suitable tools and add even pressure around
the tub.

After inlay the bearing seat, check if the claw is installed to proper position from the outside

of the twin-tub (Figure 12).

Figure 11

Figure 12

Right

Wrong

Screw

Model:HWM80-27S

Twin-tub Washing Machine

«
...
8
9
10
11
12
...
»

Summary of Contents for HWM80-27S



















Reviews:

No comments