background image

Trouble-shooting Answer  to question

(If  there's  breakdown,  please pull  off the power  plug  before checking) The following
 phenomena  are not  breakdowns  sometimes.  Please  confirm  again  before sending
 it to repair.   If there are real  breakdowns,  please  come to  the  special  maintenance 
department or after-sale service department of our company. Do not repair it by yourself.

Phenomena

  The reason

The machine does
 not act.

Is there power failure?
Is the power plug loose?
Is the pulsator twisted by foreign materials?

Is the drain hose put down?
Is the drain hose frozen?
Is the drain hose blocked by foreign material?
Are there laundries falling to the outer side of
 the spin tub?

The draining does
not work

Are there hair pin, coins or metal items brought
 inside the tub?

Is the machine slanting?
Is the gland pressed evenly?
Are there laundries falling to the outer side of
the spin tub?
Are the laundries in spin tub too much?

It is the water remained in the factory inspection
of performance.

There may be some

waterflowing  out  of

the  drain hose  in  the

first  use  of the

machine.

There's abnormal 
sound and violent
 vibration during 
spinning

There's abnormal 
soundduring washing

17

Summary of Contents for HWM80-27S





















Reviews: