background image

Back

Front

Soft items

Screw

Bottom plate

The largest allowable slope of the shank base of the machine is 2

.The slanting or rough ground will result in

unstable running or stoppage of the machine. Please adjust it with following methods:

Confirm it's horizontal:
Hang the lead line to check if it is 
horizontal.

 Adjust the adjustable leg:

Fasten

Loosen

High

Low

the adjustable nut

the adjustable leg

1 .To twist the adjustable leg, please first lift up the
    side of the leg slightly, loosen the adjustable nut,
    and twist the leg.
2 . After adjustment, fasten the nut.

Please  install and adjust the machine according to the requirement of  the mannual.
It  is very  important  to your security  and  correct operating  the machine.

Adjust the Installation position

Installation and adjustment

3 Push the " WATER LEVEL "button,select suitable water level

After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically.  To select other water level, first push the  "start/pause"
button,  then push the "water level" button to set the water level.

4 Push the "PROGRAM/RESERVE" button to select suitable reserve
   wash program

After switching on the power, the reserve program is  set to off mode automatically. If you need to
set the washing procedure to be finished at reserved time, please push the "PROGRAM/RESERVE"
button to set the reserve wash program two seconds. Refer to "PROGRAM/RESERVE"
button in Page 11 for selection.

5 Push the "Start/Pause" button 

6 Finish washing

After finishing wash

it will switch off power automatically

Install the bottom plate

After  you  open  the package, please lean 
the washing machine gently down on soft 
items ( like the towel cloth,blanket, etc. ). 
Install the bottom plate to  the bottom of the
machine  with  the  eight screws  by a cross
screwdriver, then lift the machine up gently.
See to the figure:

1.Press downward to assemble.
2.Pull upward to detach.

Install the lint filter

the washing will be finished after 18 hours.

Summary of Contents for HWM75-0528 A











Reviews: