Maintenance
Trouble-shooting
14
15
Remove
The lint filter must be used during washing.
It must be cleaned in time after each using.
Clean the detergent box and set it on the
control panel seat.
1.The method of dismantle: Push it up
aslant and gently.
2.The method of clean: Use a brush and
duster cloth to clean it, then flush it with
water.
3.The method of install : Install it
upwards and aslant and push it in.
Down
Install
Dismantle
Down
Up
Up
The front cover of the lint filter
The back cover of the lint filter
Dismantle
Install
The mehods of dismantle and install lint
filter as follows:
Remove the power plug before carrying out any cleaning or maintenance.
Clean the lint filter(s) and detergent box after each wash,otherwise it may influence
you using the machine.
The filter at the water inlet valve may
become blocked by impurities in the
water supply.Clean it with a plastic
bristled brush every two months.
If the cabinet is dirty,wipe it with a damp cloth
Do not wash directly with water.
1.After washing cycle has finshed,turn off the water faucet.(If needed,you can remove
the water inlet hose).
2.Do not store water in the washing machine for a long period without completing a
wash cycle.Drain the water completely after each wash.
3.Hang up the power cord and drain hose.
4.Wipe up any drops of water on the surface of the machine and inside the tub.Leave
the lid open for about 1 hour after each wash to evaporate any residual water.
Wipe with a neutral detergent(please check
directions on detergent bottle firse).
Do not wipe machine with thinners,petrol,
alcohol or other hash solvents.
Figure 1
Figure 2
1.Push down spring piece of the top lint
filter to make the claws out of the filter
cover,and then pull out the lint filter to get
it down.(figure1)
2.Push the back of the lint filter,and then you
can get down it off the front cover of the
lint filter.(figure2)
3.Sweep the lint in the lint filter.
4.Put the back of the lint filter into the front
cover.
5.Put the lint filter into filter cover,and make
it tight.
6.Make sure the lint filter well installed,or it
can influence your use.
Communication failure
between display board
and motor driver.
The display shows FC.
Redistribute the load evenly.
Push the Start/Pause button
once.
Level the machine.
The display shows E4.
The display shows FA.
Is the water tap closed or
has the water supply been
interrupted?
Is the water inlet valve
blocked?
Is the water pressure too
low?
Open the water tap. Push
the Start/Pause button once.
Clean the water inlet valve
then push the Start/Pause
button once.
Use after the water
pressure is normal.
The water level sensor
has failed.
The machine
does not work.
Will not
wash
Will not
spin
There are abnormal
sounds inside the machine.
Is the machine level?
Has the laundry been placed
unevenly in the machine?
Are there any foreign objects
inside the bowl?
Level the machine.
Redistribute the load evenly.
Close the top lid.
Remove the foreign object.
Is the power plug inserted
tightly?
Is the top lid closed?
Is the laundry distributed
unevenly in the machine?
Insert the power plug tightly
.
Close the top lid
.
Redistribute the laundry.
Is there a power failure?
Is the power plug inserted
tightly?
Has the water level reached
preset position?
Wait for the power supply
to be restored.
Insert the power plug tightly
.
Wait for the water to fill to
the preset level
Please contact Customer
Care.
If there is a fault or the machine dose not operate correctly,remove the power plug
before checking the machine.Using diagnostic list below,please check if the machine
requires a repair.If a repair is required,please contact our customer care team,do not
try to fix it by yourself.
The machine does not drain
or drain slowly.The display
shows E2.
The machine stops running
The display shows E2.
The machine does not drain
or drain slowly.The display
shows E3.
Has the laundry been placed
unevenly in the machine?
Is the machine level?
Is the drain hose blocked?
The top lid is not closed.
Remove the blockage.Push
the Start/Pause button once.
Close the top lid.Push the
Start/Pause button once.
Problem
Possible causes
What to do
Please contact Customer
Care.