background image

Midway spinning

Push

Push

Proper

Proper

Outer cover of 

 the spin tub

Inner cover of

 the spin tub

The laundries

are slanting

Gland

No gland

1.

Put the laundries into the spin tub evenly and smoothly.

2.

Spin

 

(1) Put the gland in properly.

     Please put in the gland properly even if the laundries quantity is small.

(2) Close the inner and outer cover of the spin tub.

(3) Spin for 1-2 minutes.

9

3.

Run the foam-removing spinning.

 1

    

 

2

Set the inlet selector handle on spin side and 

           fill water for about 1 min.

Close the spin tub outer cover and spin 

           for about 1 - 2 min.

In case water flows out from wash tub side 

due to too much inflow, please turn down 

the water tap a bit.

WATER INLET SELECTOR

WASH

SPIN

Ï ´ µ Ó Ë ³ Ð ò

Not set the switch to  

  DRAIN during washing

Wash timer

(To set to below 2 minutes,
first set to 6 minutes then
turn it back.).

Wash selector

 (Strong  current,
Standard current)   

Drain selector

 Spin timer

 (To  set  to below 1 minute, 

 first  set  to  2  minutes then 

 turn it back. it can increase

 the service life of the timer).

WATER INLET SELECTOR

Page7

Page7

WASH

SPIN

1.Water-filling selector
   1  Set the water inlet selector at the "WASH" side.
   (Figure 1)
   2  Set the water level adjusting lever to needed line.

2. Fill the water and add the dissolved washing 
   powder to make the water level reach the preset 
   position. (Figure 2)
   Run washing program for some time to stir and 
   dissolve the powder completely.

3.Put in the laundries. If the water quantity is 
  insufficient, please add water.

4.Select the current.
   Select the strength of the current according to
   the laundries. (Figure 3)

5.Select the washing time
   Select the washing time according to the laundries. 
    (Figure 4)

6.After washing, set the "WASH SELECTOR" 
   at "DRAIN". (Figure 5).

Wash

Figure 1

Figure 2

Figure 3

Figure 5

Figure 4

   Remarks:
   1. 0~15 minute is the normal  washing.
   2. 15~45 minute is  active soaking. During active soaking, the pulsator
       will run for 2 minutes in each 8 minutes. After the active soaking, it 
       will run normal washing for 15 minutes.
   3. If  you select soaking(i.e. turn the  knob to position between 15~45
       minutes),  be sure  to  dissolve  the  washing  powder  in advance, 
      otherwise the washing powder may result  in
      damage to the laundries.

Washing sequence

8

STRONG

STANDARD

4

4

3

3

2

2

1

1

5

5

STRONG

STANDARD

DRAIN 

DRAIN 

DRAIN 

DRAIN 

Summary of Contents for HWM108VA











Reviews: