manualshive.com logo in svg

Haier HW70-B1486-F, User Manual, Page: 19 / 20

Share
Download
Haier HW70-B1486-F User Manual Download Page 19

19

MAINTENANCE

TROUBLESHOOTING

TROUBLESHOOTING

The following circumstances do not constitute problems. Do not contact the Service Center until the problem has been confi rmed.

PROBLEM

CAUSES

SOLUTIONS

Washing machine fails to 
operate.

¬ Poor connection to the power supply.
¬ Power failure.
¬ The washer door is not properly closed.
¬ Machine has not been switched on.

_  Check connection to the power supply.
_  Check the power supply.
_  Close the washer door properly.
_  Make sure the machine is switched on.

Washing machine cannot be 
fi lled with water.

¬ The "Start/Pause" button is not pressed. 
¬ Water tap is not turned on.
¬ Water pressure is less than 0,03 Mpa.
¬ The inlet hose is kinked.
¬ Water supply failure.
¬ The program knob is not properly set.
¬ The washer door is not properly closed.
¬ The inlet hose fi lter is blocked.

_  press the "Start/Pause" button.
_  Turn on the water tap.
_  Check water pressure.
_  Check the inlet hose.
_  Ensure the water supply.
_  Set the program knob properly.
_  Close the washer door properly.
_  Unblock the inlet hose fi lter.

Machine is draining while 
being fi lled.

¬ The height of the drain hose is below 80 cm.
¬ The drain hose is in water.

_ Install drain hose within 80-100 cm of height.
_ Make sure the drain hose is not in water.

Drainage failure.

¬ Drain hose is blocked.
¬ Drain hose end is higher than 100 cm above 
the fl oor level. 
¬ The fi lter is blocked.

_  Unblock the drain hose.
_  Make sure the drain hose end is lower than 
100 cm above fl oor level.
_  Unblock the fi lter.

Strong vibration while 
spinning.

¬ Not all transportation bolts have been removed.
¬ Washing machine is located on an uneven 
surface or is not level.
¬ Machine load is over Max load.

_  Remove all transportation bolts.
_  Make sure the washing machine is on 
an even surface and levelled.
_  Reduce amount of laundry in the drum.

Operation stops before 
completing wash cycle.

¬ Water or electricity failure.

_  Check the power supply.

Operation stops for a period 
of time.

¬ Washing machine gives an error message.
¬  Washing machine is in soaking cycle?

_  Check display codes.
_  Press the rinse hood button or the Start/pause  
     button again to cancel it.

Excessive foam in the 
drum, which is spilled to the 
distribution drawer.

¬ The detergent is not a low-foaming type or for 
manual wash.
¬ Excessive use of detergent.

_  Check if your detergent is appropriate.
_  Reduce amount of detergent in the distribution 
drawer.

Automatic adjustment of the 
washing time.

¬ The washing program duration will be adjusted   _ This is normal and doesn't affect the 

functionality.

Spinning fails

¬ Unbalance of the laundry

_ Add clothes or run a spinning program again. 

Summary of Contents for HW70-B1486-F





















Reviews:

No comments