Haier HFD647AS, User Manual

Page: 18 / 22

Available on some models
ok
FRZTEMP REFTEMP
FUNCTION
Do not put hands or other items into the water dispenser or ice storage box.
When preessing the water dispenser tab the first time you may not get water out as air will be in the
g
Please throw away the first 5 cups of water to remove any impurities in the lines.
If you like very cold water first add some ice cubes from the ice storage box.
g
g
1.Push the dispensing pad gently,using a glass cup.
2.If you want to stop the flow of water,release from the dispensing pad.
Changing the water filter cartridge
Change the filter after 6 months.
It is not necessary to turn off the water supply before attempting to change the water filter
cartridge.
1 Grasp and firmly twist the cartridge in an anticlockwise direction (to the left when installed
in the recommended orientation) as shown in Diagram 1.
2 Pull the cartridge away from the filter head (down when installed in the
recommended orientation) as shown in Diagram 2.
– It is not unusual for a few drops of water to be present when the filter is removed.
3 Discard old filter.
4 Filter installation:
– Remove protective cap on spigot on head.
– Push the cartridge up towards filter head while rotating it in a clockwise direction (to
the right when installed in the recommended orientation) as shown in Diagram 3.5
5 Dispense 10 L (10 qt) to flush the cartridge, removing trapped air and harmless carbon fines.6
Diagram 2
Fig.
3
Waterline connection
to refrigerator
INLET
Diagram 4
Fig.
5
Locking key
Fig.
1
PRV connection
Diagram 1
Diagram 3
Fig.
4
Tap connection
Installation instructions:
1. Ensure that refrigerator is not plugged into a power
supply.
2. Locate isolation tap for water connection – cold water
feed only (dishwasher or sink mixer taps) – if you can’t
find the connection tap, contact an authorised plumber in
your state or town to fit your water connection. Tee and
tap fitting not supplied.
3. Connect the 200 mm (8”) blue tubing to the outlet of the
PRV (blue collet) and the inlet connection of the water
filter cartridge as shown in Diagram 1. Gently pull on both
ends to ensure it is locked.
4. Connect the white 6 mm (¼”) tubing to the outlet of the
water filter cartridge as shown in Diagram 2. Gently pull
to ensure it is locked.
5. Measure the required length of tubing to run from the
PRV to the water connection point.
6. Cut the tubing making sure the ends are square and
clean.
7. Connect the tubing to the tap connection and the base of
the PRV (white collet) and then to the tap as shown in
Diagram 3. Please note that the tap connection supplied
should fit most installation situations. If your tap requires
a different fitting, please contact an authorised plumber in
your state or town to purchase the correct fitting.
8. Connect one locking key to each side of the water filter
cartridge in between the cartridge and the locking collet
as shown in Diagram 4.
9. To flush the water filter and check for leaks, aim the end
of the tubing into a bucket, turn isolating tap on and run
at least 3 L (3 qt) of water through. Once complete, turn
isolating tap off.
10. Locate desired position for water filter noting carefully the
following points:
• It is recommended to fit the water filter in a vertical
orientation with the water filter head at the top. This
will minimise water leakage when replacing cartridge.
• Ensure the filter is in a convenient location to access
every 6 months for replacement. We suggest that this
location is beside the water filter supply tap in a
cupboard beside the refrigerator.
• A minimum clearance of 64 mm (2 ½”) from the
bottom of the filter cartridge is required to perform
cartridge removal.
• Do not screw the water filter to refrigerator.
How to Use the Water Dispenser
First Use
Water Dispenser Precautions
26