Haier HB21FC45N Series Service Manual Download Page 12 | Manualshive

Page: 12 / 45

background image

SERVICE MANUAL

Model: HB21FC45N*

12

Issue 2010-07-05

Rev. Ref1007S019V0

3-2 Installing and Removing Door

Precautions During Dismantling and Installation of The Door

You may not need to remove the doors! But if you have trouble getting the unit into its final

lacation,please follow the below door removal and installation instructions. It is suggected, for your

safety, to have two or more people to assist you in completing the below task to avoid bodily injury,

product damage,or properly loss.

3-2-1. Right French Door Removal and Installation

1. Remove the screws on the top hinge cover

2. Using a screwdriver,remove the top hinge screws.Remove the hinge, then take the refrigerator

door off and place it aside for the time being.

3. Remove the middle hinge,if needed.

4. Install the refrigerant door in reverse sequence,

When lifting up the refrigerator hinge and separating it from the door body,please be careful not to

drop the door slanted forward.

«
...
10
11
12
13
14
...
»

Summary of Contents for HB21FC45N Series














































Reviews:

No comments

Related manuals for HB21FC45N Series

Brand: Saivod Pages: 26

Brand: Zanussi Electrolux Pages: 16

Brand: Iceking Pages: 12

Brand: Magic Chef Pages: 9

Brand: Saba Pages: 39

Brand: Howard McCray Pages: 8

Brand: U-Line Pages: 47

Brand: Rangemaster Pages: 40

Brand: Magic Chef Pages: 8

Brand: Laurus Pages: 128

Brand: Magic Chef Pages: 5

Brand: Accucold Pages: 16

Brand: DAEWOO ELECTRONICS Pages: 83

Brand: GE Pages: 20

Side by Side 26

Brand: GE Pages: 72

GSF25TGTBBB and

Brand: GE Pages: 112

GSW25LSTESS and

Brand: GE Pages: 280

Monogram BIS42CKB/C

Brand: GE Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands