Haier HA500TX, Operation Manual, Page: 4 / 17

ዤᅎ฾၀
ဆᄮࣴէᆍอƬ്ྖਜࣴயƬ݂ኝᆚᅘྪईࣴயԣරఙਜƬဆᄮࣴླྀէᄖ༏ຶ૽٤Ƭᅀௌ
ֻ೼էᅃ౫؀ç
ƴէᄖඈဆ࣬ࢂީࡈಃ௵၂॰࣬રຠٵႄհ
૽ڊ࿣಻ç
ƵဆᄮഒƬᅰॡᄮ࿣෭ڊ੽ૢ੽෭Ƭᄮ੍æᄮ
٠ڎ଑ໃ࿣ॖࡩਜေ؎ݮ࡟Ƭညၑ࿣಻ටྲྀ
ጕæ٠ጕæႈቜڎᅰ݇ණဆᄮ٤࣬ታཌྷ༏ఢဆ
ڙƬᅀௌညၑ࿣಻ࢦණဆᄮࣴఢླྀ཈ኒ़ڊੇ
ဈኴç
ሂኘႀזႢೞ़էᄖٚਜဆڙङݘಊ೻࡬
ᅀௌဆڙङׯէ৏ç
ࣴயฆᆚ጖໒ӱဧዲኧဆᄮࣴזႢগ๴࣬
۳ڭ ݘ኷࢏ܿ਻ٚਜࣴயലटሂسኒ
ഒէᄖഡႀਜயᅀௌ໊ࢯயӱဧ!ဆᄮࣴఢ
ຈྯֶ࠻ؘ࠙֘ڬနԭᇝอ്࿤ٚਜࣴயç
னضဆڙগ๴࢏ᅰࠖԣຈନཌྷᅀௌᅞຈჇ
Քۓܤธଵຈæถຈဨ၅ƻՎҾနڭᇜ֑ཌྷƬ
ॡؘ࠙֘ڬन֏േઽީ৏Ƭᅀ݂ለ࿣ሁضሹ
ڃᄮ࿣෭࣬ีؘڬԻௐܤணç
Ƴဆᄮࣴ໠ௐ෭էᄖ݇ኧኼ࿣æܤඈ೻৳ई
ᅃଵຈଵᄦ༝ڊ࿣಻Ƭᅀௌڂኦ໠ௐӕईຶ૽
ॖڊԲၾç
޶ນࣛٵ؀Ƭྞӱ࢞ూڊ
ဆᄮࣴƬ്ല࿤ࣴဆ׎ᆚ
޶ນڊႈቜ
3 12
Maintenance
6. If the machine is to be moved a distance location,
replace the vibration mounting locks which were re-
moved during installation as shown below.
1. Turn of the water and electricity supply
after every wash. Open the door to pre-
vent the formation of moisture and odors.
If the washing machine is left idle for a
long period, drain any remaining water in
the machine and replace the drainage
hose. 2. Unplug the machine during cleaning and
maintenance. Use a soft cloth dampened with
soapy liquid to clean the machine case and rub-
ber components. Do not use corrosive or abra-
sive chemicals or solvents.
3. Clean the detergent compartment
regularly. For the detergent compartment
similar to figure (a), raise the compartment
slightly to remove and replace after cleaning.
7. If the washing machine is left idle
for a long period turn off the water
and electricity supply and open the
door slightly to prevent the formation
of moisture and odors.
5. To prevent block-
ages to the water sup-
ply or the ingress of
contaminants, clean
the water inlet and in-
l e t w a t e r f i l t e r
regularly.
ၦန࢏ާӕ
෭࡟࢏ާ
ᆍߢ৳পࠊ୩ຂ
֑ණӬዲᆍࠊی୩ຂ
ൡနߖ݂ड़ຶ૽ۦ
4. Cleaning the Filter (once a month)
Press the lower edge of the filter compartment
cover to open; (Fig1-2)
Remove the filter by turning counterclockwise;
(Fig3)
Flash clean with running water;
Filter replacement is the reverse of removal. Cau-
tion: Attention shall be paid to ensure that the fil-
ter is replaced correctly to avoid possible leakage.
fig.1
Replace the back
cover.
Remove the
back cover.
Replace the rubber
plugs.
Insert the bolts.
Tighten the bolts with the
spanner provided.
fig.2
fig.3
Fig (a)