Haier EK Series, Service Manual

Page: 26 / 81

4
6
5
2
1
4
3
Inlet grille
Inlet
Air Purifying Filter (inside)
Outlet
Horizontal flap
6
4
2
1
5
3
Parts and Functions
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
adjust up and down air flow Don't adjust it manually
adjust left and right air flow
Vertical blade
Remote controller
If the unit which you purchased has healthy function,follow it.If not,please ignore.
NOTE:
Cooling only unit do not have displays and functions related with heating
(inside)
Power indicator
Timer mode indicator
Operation mode indicator
(Lights up when unit starts.)
(Lights up whenTimer operation is selected.)
(lights up when the compressor is on.)
Remote signal receiver
(A beeping sound is generated when a signal
from remote controller isreceived.)
Ambient temp display
When receiving the remote control signal, display the set
temperature and in the rest time the room temperature is
is displayed and this room temperature is only for reference.
7
11
10
8
9
Anion generator
12
Outdoor Unit
14
Indoor Unit
OUTLET
INLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
1
2
3
4
1
2
3
Remove the battery cover;
Load the batteries as
illustrated. 2 R-03 batteries,
resetting key(cylinder);
Be sure that the loading
is in line with the " + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
so the distance to the indoor unit should be shorter.
wireless telephone is installed in the type fluorescent lamp or
room, the receiver is apt to be disturbed in receivingthe signals,
Note:
Full display or unclear display during operation indicates the
ries have been used up.Please change batteries.
If the remote controller can't run normally during operation,
reload several minutes later.
batte
remove the batteries and
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out, just need to press reset key
Hint:
Loading of the battery
please
Clock set
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press
change quickly. After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
or decrease 1min. If the button is kept pressed,time will
will increase
TIMER
CLOCK
SET SLEEP
FAN
DRY
COOL
AUTO
1. Mode display
2. SWING display
3. FAN SPEED display
4. SLEEP display
5. LOCK display
6. SIGNAL SENDING
7. TIMER OFF display
8. TIMER ON display
9. CLOCK display
10. TEMP display
11. POWER ON/OFF
Used for unit start and stop.
12. MODE
Used to select AUTO run, COOL,
DRY
,
HEAT and FAN operation.
13. FAN
Used to select fan speed LO,
14. HOUR
Used to set clock and timer setting.
15. SWING
Used to set auto fan direction.
16. SLEEP
Used to select sleep mode.
17. LOCK
Used to lock buttons and LCD display.
18. TEMP.SETTING
Used to select your desired temp.
LO MED HI AUTO
HEAT
6
7
8
9
10
4
ON/OFF
FAN
MODE
SWING
TIMER
CLOCK
SET SLEEP
LOCK RESET
11
18
19
20
21
19. SET /
Used to confirm timer and clock
settings.
20. TIMER
Used to select TIMER ON,
TIMER OFF,TIMER ON-OFF
21. CLOCK Used to set correct time
22. RESET
Used to reset the controller back
LIGHT
HEALTH
23
23. HEALTH
Used to operate the healthy function
MED, HI, AUTO
to normal condition.
and LCD display.(This function is
1
2
3
5
13
12
14
15
16
17 22
unacailable on some models.)
5
2
1
5
3
6
7
4
8
9
10
11
12
+68
18HEK03
Все каталоги и инструкции здесь: http : //splitoff.ru/tehn-doc.html