background image

1.2.6 Take Care to Deal With The Cathode-Ray Tube

 

In the condition that an explosion-proof cathoderay tube is set in this equipment, safety is se-cured 

against implosion. However, when removing it or serving from backward, it is dangerous to give a 

shock. Take enough care to deal with it. 

1.2.7 Safety Check after Repairment

 

Confirm that the screws ,parts and wiring which were removed in order to service are put in the 

original positions, or whether there are the portions which are deteriorated around the serviced 

places serviced or not. Check the insulation between the antenna terminal or external metal and 

the AC cord plug blades. And be sure the safety of that. 

Insuration Test

 

1. Unplug the plug from the AC outlet. 

2. Remove the antenna terminal on TV and turn on the TV. 
3. Insulation resistance between the cord plug terminals and the eternal exposure metal 

should be more than M ohm by using the 500V insulation resistance meter 

4. If the insulation resistance is less than M ohm, the inspection repair should be required. 
If you have not the 500V insulation resistance meter, use a Tester. 

External exposure metal: Antenna terminal Headphone jack 

1.2.8 Ordering Spare Parts

 

Please include the following informations when you order parts. (Particularly the Version 
letter) 
1. Model number and Version letter 

The model number can be found on the back of each product and the Version letter can 
be found at the end of the serial number. 

2. Part No. and Description 

You can find them in your service manual

1.2.9 Photo used in this manual

 

The illustration and photos used in this Manual may not base on the final design of products, which 
may differ from your products in some way. 
 

1.3 How to read this Service Manual

 

1.3.1 Using Icons

 

Icons are used to attract the attention of the reader to specific information. The meaning of each 

icon is 

described in the table below:

 

 
 
 

Note:

 

A “note” provides information that is not indispensable, but may nevertheless be valuable to the 
reader, such as tips and tricks.

 

Caution:

 

A “caution” is used when there is danger that the reader, through incorrect manipulation, 

                    

                                             

                          

Summary of Contents for DX-LDVD22-10A












































Reviews: