Starting the appliance
.6.
GB
Switching the machine on ...
After having completed all of the installation steps in the pre-
ceding paragraphs, turn on the water to the unit, partially open
the door of the dishwasher, and press the ON-OFF button “A”
located on the control panel. The indicator light “B” will come
on. At this point, the appliance is on and ready to be
programmed.
Setting and starting a wash Cycle
…
Choose the required cycle by pressing the cycle selection but-
ton “G”. Each time it is pressed, one of the cycle indicator lights
“F” will begin to blink in succession.
Choose the wash cycle you feel is most appropriate for the type
of dishes that need washing (consult the wash cycle table con-
tained in this manual, especially when first using the appliance).
Close the door and the wash cycle will begin. If necessary, read
the paragraph entitled, “Cancelling or modifying a cycle" The
end of the cycle will be signalled by six beeps, and the indicator
light “F” will turn off.
Cancelling or modifying a cycle while underway...
Memory function module
If the dishwasher is switched off through the ON/OFF button,
or a power cut happens while the selected washing program is
active, the program is not cancelled. The controls use a micro-
processor device, to memorise the information about the se-
lected washing program. Once the machine is powered on again
, the cycle will resume.
Cancelling or modifying a washing program cycle
1: To modify or cancel a washing cycle in progress, it is neces-
sary to reset the previous programming. To do this hold down
the programme selector button “G” for at least 3 seconds, and
the buzzer will emits a short warning signal.
2: If the reset operation was successful, the drain phase is
started. Once the drain phase is ended, the dishwasher can be
reprogrammed.
NOTE: A cycle that is underway can only be modified if it has
only been running for a short time.
Otherwise, the detergent may have already been used and the
appliance may have already drained the wash water. If this is
the case, the detergent dispenser must be refilled (see the para-
graph entitled, “Loading the Detergent”).
To change a cycle currently underway, open the door and press
the ON-OFF button “A”. Follow the instructions in the paragraph
entitled “Switching the machine on...”, ”Setting and starting a
wash cycle”.
To set a new wash cycle, follow the instructions contained in
the paragraph entitled, “Setting and Starting a Wash Cycle”.
If you forget to load some of the dishes...
The wash cycle can be interrupted by opening the door care-
fully (in order to avoid being sprayed by hot water). When the
door is closed again, the cycle will automatically restart at the
point where it left off after 30 seconds .
At the end of the wash cycle...
The end of the cycle will be indicated by six beeps, at the same
time the indicator light “F” will turn off. Open the door and turn off
the appliance using the ON-OFF switch. Wait a few minutes be-
fore removing the dishes so as to avoid handling them while still
hot (when they are more susceptible to breakage) and to get
better drying results.
Setting the start delay time
Partially open the door of the dishwasher. If you press button “J”
(see Close-up View ”Control Panel”). the start time for the wash
cycle will be delayed in increments of 2 hours up to 12 hours.
Each time the button is pressed, light “I” will indicate the length
of the delay.
After selecting the delay time, set the wash cycle, as explained
in the section entitled “Setting and starting a wash cycle”.
Close the door and at this point the delay period will begin to
count down. During this period the delay indicator light (I)
will come on. At the end of the delay time, the indicator will turn
off and the cycle will start.
NOTE:
a) During the delay period, none of the settings can be modified.
If necessary, they can be cancelled by pressing press the ON-
OFF button “A” located on the control panel.
b) If the door is opened during the delay period, the clock will
stop the countdown. It will start again when the door has been
closed.
Wash cycle adjustment buttons
1/2 load button
This button (see” Close-up view on the Control panel”, letter “C”)
makes it possible to wash dishes using only the upper rack if
there are not enough dishes for a full load. This will allow you to
save water and energy.
