background image

16

The wiring for the power line of indoor unit, the wiring between indoor and outdoor units as well as the wiring between 

indoor units:

Electrical Wiring

SW01_

1

SW01_2

 

SW01_3

 

SW01_4

Wired control address

[1]

[2]

[3]

[4]

Wired control address

0

0

0

0

Master unit in group control

0

0

0

1

Slave unit 1 in group control

0

0

1

0

Slave unit 2 in group control

0

0

1

1

Slave unit 3 in group control

∙∙∙

∙∙∙

∙∙∙

∙∙∙

∙∙∙

1

1

1

1

Slave unit 15 in group control

SW01_5

 

SW01_6

 

SW01_7

 

SW01_8

Indoor unit capacity

[5]

[6]

[7]

[8]

Indoor unit capacity

0

0

0

0

0.6HP

0

0

0

1

0.8HP

0

0

1

0

1.0HP

0

0

1

1

1.2HP

0

1

0

0

1.5HP

0

1

0

1

1.7HP

0

1

1

0

2.0HP

0

1

1

1

2.5HP

1

0

0

0

3.0HP

1

0

0

1

3.2HP

1

0

1

0

4.0HP

1

0

1

1

5.0HP

1

1

0

0

6.0HP

1

1

0

1

8.0HP

1

1

1

0

10.0HP

1

1

1

1

15.0HP

Dipswitch Setting

(A) Definition and description of SW01

                 

   Items

Total  

 

Current of 

 

Indoor Units(A)

Cross

 

Section

 

(mm

2

)

Length

 

(m)

Rated 

 

Current of 

 

Overflow 

 

Breaker(A)

Rated current of residual

 

Circuit Breaker(A)

 

Ground Fault 

Interruptor(mA) 

 

Response time(S)

Cross Sectional 

 

Area of Signal Line

Outdoor -indoor

 

(mm

2

)

Indoor -indoor

 

(mm

2

)

 

<7

2.5

20

10

1

0 A,30 mA,0.1S or below  

2 cores×0.75-2.0

 

mm

2

 shielded line

7

 and <11

4

20

16

16

 A,30 mA,0.1S or below  

≥11and <16

6

25

20

20

 A,30 mA,0.1S or below

≥16 and <22 

8

30

32

32

 A,30 mA,0.1S or below

≥22 and <27   

10

40

32

32

 A,30 mA,0.1S or below

•  The electrical power line and signal lines must be fastened tightly.

•  Every indoor unit must have the ground connection.

•  The power line should be enlarged if it exceeds the permissible length.

•  Shielded lays of all the indoor and outdoor units should be connected together, with the shielded lay at the side of signal 

lines of outdoor units grounded at one point. 

•  It is not permissible if the whole length of signal line exceeds 1000m.

Signal Wiring of Wired controller

Length of Signal Line (m)

Wiring Dimensions

≤250

0.75mm

x core shielding line

•  The shielding lay of the signal line must be grounded at one 

end.

•  The total length of the signal line shall not be more than 250m.

Summary of Contents for AC092MDERA

























Reviews: