haibike XDURO Owner'S Manual Download

Page: 22 / 82

Currie Tech

Technical and Customer Service: +1 800-377-4532

5 Safety indd

Last Modified March 27, 2014 10:33 AM

Safety

After an accident

Changing the components on your bike

with other than genuine replacement

parts may compromise the safety of

your bicycle and may void the warranty.

Check with your dealer before changing

the components on your bike.

Choking hazard: Some bicycle acces-

sories may present a choking hazard to

small children. Keep these accessories

away from small children.

After an accident

After an accident, you must consider

your bike unsafe to ride until you follow

the instructions in this section. Failure

to follow the instructions in this section

could lead to component failure, injury,

or death.

Before performing ANY service, inspec-

tion, or maintenance on your electric

bicycle, you should first remove the bat

tery. Failure to remove the battery could

lead to the bicycle turning on unexpect-

edly, causing serious damage or injury.
If you have to perform maintenance that

requires the battery to be installed, you

must be sure that even if the bicycle

wheel, chain, or other drivetrain com-

ponents begin moving unexpectedly,

they will not be in a position to cause

injury or damage.

Be sure to read, understand, and comply

with the drive system user manual. Do

not disassemble or attempt to service

components unless explicitly allowed by

the manufacturer.

Check the rechargeable battery. If the

rechargeable battery is no longer prop-

erly in its holder or shows any damage,

do not use your bike any longer, at least

not in assistance mode. Switch off the

motor and the battery separately, if nec-

essary. A damaged battery can lead to

a short-circuit or a sudden failure of the

electric assistance right at the moment

when you need it.

Damage to the outer housing of the

rechargeable battery can result in the

entry of water or moisture and that can

lead to short circuits or electric shocks.

The rechargeable battery could catch fire

or even explode! In such a case contact

your bicycle dealer immediately.

Check whether the wheels are still firmly

fixed in the dropouts and whether the

rims are still centered with respect to

the frame or fork. Spin the wheels and

observe the gap either between the

frame and tire or between the brake

pads and rim sides.

If the width of the gap changes markedly

and you have no way to true the wheel

where you are, you will need to release

the rim brake a little so that the rim can run

between the brake pads without touching

them. Please note that in this case the

brakes may not act as powerfully as you

are used to.

For more information, see “Wheels with

cam action systems” on page 25, “Brakes”

Summary of Contents for XDURO



















































































Search results

Summary of Contents for XDURO

Reviews:

Related manuals for XDURO

Brands by name

Popular brands

haibike XDURO, Owner'S Manual

Search results

Summary of Contents for XDURO

Reviews:

Related manuals for XDURO

Brands by name

Popular brands