4 Programming
OUTER
RECEIVER
1
2
3
INNER
RECEIVER
4
1 DIP SWITCH SETTINGS
2 HAND HELD CONFIGURATION
1. Set dip switches on the receiver to the desired activation cycle (dip switch 1 -Toggle or Pulse and dip switch 2 - 0.5s or 10s hold).
2. Press either Learn w/Delay Button or Learn w/No Delay Button on the receiver depending on the activation requirements
(If delay learn is selected, adjust potentiometer to counterclockwise limit, 0 second delay). After learn cycle is complete, adjust
potentiometer to desired delay time (0-30 sec).
3. Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter).
NOTE: Repeat Steps 2-3 to program additional transmitters.
4. To test the system, depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the
receiver. This indicates that the relay has been activated.
3 PUSH PLATE CONFIGURATION
1. Before beginning, it is easiest to have already prepared the installation of the push plate.
2. Connect the wires from the transmitter to the NO and COM contacts of the push plates switch.
3.
Follow Steps 1-4 (Hand-Held Configuration); depress the pushplate to activate the transmitter
.
4. Attach the transmitter to the inside of the electrical box and complete the installation.
4 TYPICAL VESTIBULE APPLICATION
5 REMOVING TRANSMITTER CODE(S)
A OUTSIDE TRANSMITTER (PUSH PLATE)
1. Press Learn w/NO DELAY BUTTON on OUTER Receiver then press Transmitter 1.
2. Press Learn w/DELAY BUTTON on INNER Receiver then press Transmitter 1.
NOTE: Set Potentiometer to desired Delay T
ime per Hand Held Configuration Step #2.
B INSIDE TRANSMITTER (PUSH PLATE)
1. Press Learn w/NO DELAY BUTTON on INNER Receiver then press Transmitter 2.
2. Press Learn w/DELAY BUTTON on OUTER Receiver then press Transmitter 2.
NOTE: Set Potentiometer to desired Delay T
ime per Hand Held Configuration Step #2.
C VESTIBULE TRANSMITTERS (Dual Switch Push plate or Two Separate Push plates)
1. Press Learn w/NO DELAY BUTTON on INNER Receiver then press Transmitter 3.
2. Press Learn w/NO DELAY BUTTON on OUTER Receiver then press Transmitter 4.
SINGLE TRANSMITTER CODE
1. Press both DELAY and NO DELAY BUTT
ONS simultaneously until Red LED flashes once (approximately 1 second).
2. Press transmitter button twice within 10 seconds and the transmitter code will be deleted.
ALL TRANSMITTER CODES
1. Press and hold both DELAY and NO DELAY BUTTONS simultaneously until Blue LED illuminates then release (approximately 10 seconds).
# 1
DESCRIPTION
FUNCTION
OFF Pulse Relay
Press the transmitter once and the relay will be active momentarily.
ON
Toggle Relay
Press the transmitter once and the relay output is active indefinitely
,
press it again and the relay will de-energize indefinitel
y.
# 2
DESCRIPTION
FUNCTION (Pulse Mode Only)
OFF 0.5 sec Hold Time Relay will remain active 0.5 second after the loss of activation.
ON
10 sec Hold Time
Relay will remain active 10 seconds after the loss of activation.
1 2
ON
0.5s l 10s
PUL
TOG
1 2
ON
0.5s l 10s
PUL
TOG
In Toggle Setting (1-ON), the Hold Time
is inactive. Either setting for #2 dip
switch will have the same result.
1 2
ON
0.5s l 10s
PUL
TOG
1 2
ON
0.5s l 10s
PUL
TO
G
0.5 second
Pulse Setting
10 second
Pulse Setting
07/24/2013 Hager Companies • 139 Victor Street • St. Louis, MO 63104 • 800 325 5559 • www.hagerco.com Page 2 of 4
433 MHz Transmitters & Reciever
Installation Instructions
Digital Transmitters and Receiver with Sequencing Function
I-EA00116
433 MHz Transmitters & Reciever
Installation Instructions
Digital Transmitters and Receiver with Sequencing Function
I-EA00116
