background image

Dear customer,

We thank you and congratulate you on

your choice.

This new carefully designed product,

manufactured with the highest quality

materials, has been carefully tested to sa-

tisfy all your cooking demands.

We would therefore request you to read

and follow these easy instructions which

will allow you to obtain excellent results

right from the start.

May we wish you all the very best with

your modern appliance!

THE MANUFACTURER

APPLIANCE

 

IS

 

CONCEIVED

 

FOR

 

DOMESTIC

 

USE

ONLY

THE

 

MANUFACTURER

 

SHALL

 

NOT

 

IN

 

ANY

WAY

 

BE

 

HELD

 

RESPONSIBLE

 

FOR

 

WHATEVER

INJURIES

 

OR

 

DAMAGES

 

ARE

 

CAUSED

 

BY

INCORRECT

 

INSTALLATION

 

OR

 

BY

 

UNSUITABLE

,

WRONG

 

OR

 

ABSURD

 

USE

.

- The appliance is not intended for use by young children or infirm

persons without supervision.

- Young children should be supervised to ensure that they do not play

with the appliance.

- If the supply cord is damaged, it must be replaced by the manufacturer

or its service agent or a similarly qualified person in order to avoid a

hazard.

- If a stationary appliance is not provided with a supply cord and a plug

or with other means for disconnection from the supply having an air gap

contact separation in all active (phase) conductors, the instructions shall

state that such means for disconnection shall be incorporated in the fixed

wiring according to the wiring rules.

For service please reFer to service address 
and number reported in the warranty card.

-  Where this appliance is installed in marine craft or in caravans, it shall 

not be used as a space heater

-  Do not spray aerosols in the vicinity of this appliance while it is in ope-

ration.

Summary of Contents for 539.07.241













Reviews: