HADEF 340/15 Installation, Operating And Maintenance Instruction Download Page 11

 

 

 

 

5.52.734.00.01.00 

 

 

11 

 

14 

Trouble 

 

 

Please pay attention to the following in case of problems: 

  Troubles with the equipment must only be repaired by qualified personnel. 

  Secure the unit against unintended operation start. 

  Put up a warning note indicating that the unit is not to be used. 

  Secure the working area of moving parts of the unit. 

  Please read the chapter "Safety instructions". 

Notes on the repair of faults are found in the following table. 

For the repair of failures please contact our service department. 

 

 

 

   

CAUTION!

 

Trouble  caused  by  wear  or  damage  to  parts  such  as  wire  ropes,  chains,  chain  wheels,  axes,  bearings, 
brake parts, etc., must be remedied by replacing the parts with original spare parts. 

 

 

15 

Remedy 

 

 

Problem

 

Cause

 

Remedy

 

Jib is hardly to slew 

Bearings inhibited by overload 

Maintain 

– change bearings 

Jib - deformed 

Overloaded 

Check jib and bracket 

– if so, change it 

 

16 

Decommissioning 

 

 

   

WARNING!

 

It is essential that the following points are observed in order to prevent damage to the equipment or critical 
injury when the device is being decommissioned: 

 

 

It is mandatory that all steps for decommissioning the machine are carried out in the indicated sequence: 

  First secure the working area for decommissioning, leaving plenty of space. 

  Read the chapter "Safety instructions". 

  Disassembly is carried out in reverse order to the assembly.  

  Please make sure that all operating material is disposed of in accordance with environmental regulations. 

16.1 

Temporary decommissioning 

  Measures are as above.  

 

Also read the chapter “Transport and storage”. 

16.2 

Final decommissioning/disposal 

  Measures are as above.  

  After disassembly, ensure that the disposal of the equipment and any materials it contains is carried out 

in accordance with environmental regulations. 

 

 

 

17 

Additional documents 

 

 

17.1 

Operating instructions for cranes 

acc.  to  the  accident  prevention  regulations  for  "cranes",  are  attached  to  the  consignment  or  to  the 
documents. 

 

 

 

Summary of Contents for 340/15













Reviews: