background image

 

 

 

 

5.52.208.00.01.06 

 

 

 

2.3 

Requirements for the operating personnel 

  The units may only be operated by qualified persons that are appropriately trained and that are familiar with 
it. They must have their employer’s authorization for operation of the units. 

Before starting work, the operating personnel must have read the operating and installation instructions, 
especially the chapter "Safety Instructions". 

This is especially important for operating personnel that rarely uses the equipment, i.e. for installation or 
maintenance work. 

   

DANGER!

 

In order to avoid severe injury, please pay attention to the following when using the equipment: 

  Use protective clothes/equipment. 

  Do not wear long hair hanging down open. 

  Do not wear rings or other jewelry. 

  Do not wear clothes that are too big/wide. 

  Do not reach into ropes, chains, drive parts or other moving parts with your hands 

 

 

2.4 

Appropriate use 

The permitted safe working load of the devices must not be exceeded! An exception can be made during the 
load test before initial operation, carried out by a licensed qualified person. 

 

 

  The permissible ambient temperature during operation of manual driven devices is -20 ° C / + 50 ° C and 

at all power driven devices -20 ° C / + 40 ° C! 

  Defective devices and load suspension devices must not be used until they have been repaired! Only 

original spare parts must be used. Non-compliance will result in any warranty claims becoming void. 

  Liability and warranty will become void if unauthorized modifications of the units are made by the user! 

 

Vertical lifting and lowering of unguided loads, horizontal movement of loads and inclined movement of 
loads, movement of flaps, covers etc. 

2.4.1 

Winches with disengaging clutch (as option) 

  Only for pulling out the uncharged wire rope 

  Only for horizontal load 

  Only for special kinds of use (i.e. lowering of floaters in liquids) when there is no danger for persons or 

danger of damage of material. 

 

 

 

NOTICE!

 

If the units are not used appropriately, it is not possible to ensure safe operation. 

The owner and operator have sole liability for all personal injury and damage to property arising from 
inappropriate use. 

 

 

 

   

DANGER!

 

It is not allowed: 

 

  pulling loose of stuck loads, dragging of loads and inclined pulling is not allowed.  

  in explosive atmosphere, except the unit is especially modified for it and marked by an indication label 

  In reactor containment vessels. 

  to transport people  

  The device is not suitable for use on stages and in studios 

   persons must not stand under a suspended load 

 

 

 

 

Summary of Contents for 238/10
















Reviews: