background image

Replacement parts and accessories

Note: Product and Article numbers may vary for some selling regions. Contact the appropriate distributor or refer to
the company website for contact information.

Replacement parts

Description

Item no.

Battery compartment cover

8524400 

Battery compartment cover, O-ring

8533400 

Desiccant cap assembly (battery compartment desiccant)

8754900 

Desiccant tube assembly (battery compartment desiccant)

8535200 

Desiccant, replacement beads, 680 g (1.5 lb)

8755500 

Eyebolts, 1/4–20 x 2.5-in. stainless steel

8535500 

Gasket, top cover

8533300 

Enclosure screw, #10–14 x 1 in.

8753300 

Logger handle

8524200 

Lubricant, silicone, 0.25 oz

000298HY

Magnet assembly

8537800 

Cap and lanyard for the Sensor, Comm or Aux connectors

8535000 

Cap and lanyard for the rain gauge connector

9492500 

Power

Description

Item no.

Battery, 6 V lantern

11013M

Battery, long-life alkaline

8542900 

Long-life alkaline battery pack top cap adapter and cable

8543000 

Cable assembly, external power, 2.7 m (9 ft)

8528700 

Cable assembly, external power, 7.6 m (25 ft)

8528701 

Mounting hardware

Description

Item no.

Wall-mount bracket without ladder hanger

8542700 

Wall-mount bracket adapter

8543800 

Antennas

Description

Item no.

Blade, 3G/4G LTE, 3 dBi

8623800 

Mini-wing, 2G/3G/4G LTE, 2.5 m (8.2 ft) cable, 5.5 dBi

8624000 

English

   

25

Summary of Contents for FL900 Series































Reviews: