background image

      HAC-UM Series RF Module Manual          SHENZHEN HAC TECHNOLOGY CO., LTD.

 

FAX:+86-755-23981077 23981079             

- 8 -

                                                            www.rf-module-china.com

 

HAC-UM  standard  transceivers  offer  transparent  protocol  to  support  various  applications  and 

protocols of users. If the user needs to decrease his cost or ease the workload of terminal CPU, 

we can add other specific functions based on the transparent protocol, such as addressing, data 

acquisition, command interpretation, etc. 

 

6.

 

Sleep function instruction: 

Due  to  reducing  more  consumption,  HAC-UM  transceivers  support  Sleep  function.  In  sleep 

mode, the current consumption is less than 5

µ

A.   

The  default  set  of  sleep  function  is  usually  closed  to  ensure  the  reliability  of  preventing 

transceivers from getting in wrong sleep mode. The sleep function can be opened by HAC after 

informed or by user via programming them software. 

a. How to use the Sleep function: 

The Pin8 

SLP

 in JP1 is the signal of sleep control. In high power level, when the transceiver 

stays in sleep mode, the  conversion from idle mode to sleep will be finished in 1ms. The SLP 

signal  can  convert  transceiver  from  idle  to  sleep  mode  in  1ms  after  rising  edge.  If  the  Sleep 

signal arrives when the transceiver is transmitting data, the module will enter sleep mode after 

finishing transmission. From sleep mode to idle, it takes the transceiver 10ms after falling edge. 

To disable the sleep function of HAC-UM, the SLP (SLEEP) pin should be definitely connected 

with 0 or ground. 

b. Attentions about use of sleep function:   

When the sleep function enabled, any supply glitches, such as switch dithering, fire striking or 

quick switching on and off, could cause the transceiver to be switched to the wrong sleep mode. 

After switching on, users can avoid this error by making a compulsive restoration once after the 

CPU delays 100ms. But such a condition occurs seldom. 

c. Sleep Time Diagram: 

                   
 
 
 
 
 
 
 
 

 

 

Summary of Contents for UM Series















Reviews: