Habasit PM-1606 Page 75 General Manual Use And Maintenance Download

Page: 75 / 79

Habasit Italiana S.p.A.
Vittorio Veneto 31029 (TV)
Tel.: ++39(0)438.9113
Fax. ++39(0)438.200545

Hot Press PM-1606

Author:

S.D.T. / KM

SPARE PARTS

Edition: 02/2005

Page

I-12

Replaces: 01/2002

ABLE

PARE PARTS FOR ELECTRICAL

WATER AND AIR CONNECTIONS USED IN MOBILE OPERATION

Pos. Description M.U.

Q.ty

Assembly

code

Parts code

CABLE CONNECTION PAIR REGULATOR
PMR-04/PMR-06 AND OUTLET PM

N° 1 691011

MOBILE COOLING PUMP. The cooling pump may
depend on the electrical tension available.

N° 1

MOBILE COOLING PUMP PM-04/7 230V

N°

691016

MOBILE COOLING PUMP PM-04/6 120V

N°

691015

IMMERSION

PUMP

220V

N°

709000

IMMERSION

PUMP

120V

N°

709002

The following parts are in common irrespective of the tension applied to the pump

50 LITER BIN

N°

709003

COOLING WATER DISCHARGE TUBE PM-04/6/7

N°

700021

TUBE COLLAR - DIAM 100mm M10

N°

700500

FEMALE CONNECTION ¼” code 403 1/4SV

N°

IN020413

RUBBER HOSE FOR AIR/WATER 20 bar 25 x 37

0.16

702508

RUBBER HOSE FOR AIR/WATER 20 bar 16 x 26

702509

RUBBER HOSE FOR AIR/WATER 20 bar 13 x 23

702511

PMR-06 OUTPUT ADAPTOR

N°

IN040301

MOBILE MINI COMPRESSOR The compressor may
vary according to the electrical tension available

N° 1

MOBILE MINI COMPRESSOR MC-04/7 230V

N°

691017

MOBILE MINI COMPRESSOR MC-04/6 120V

N°

691018

MINI COMPRESSOR 220V

N°

709001

MINI COMPRESSOR 120V

N°

709004

The following parts are in common irrespective of the tension applied to the compressor

RADIAL MANOMETER ¼” GLICER 1-6 bar

N°

700516

FAUCET SERIES A/4» F-F

N°

700517

FEMALE CONNECTION 04 MINI ¼” code 0101004

N°

IN020655

COLLAR WITH TWO EARS COL-PI 11x13

N°

IN020412

PLASTIC TUBE PVC 6x12 code TA06

N°

IN020410

PMR-06 OUTPUT ADAPTOR

N°

IN040301

CONNECTION ADAPTOR DIRECT TO PMR-06
(only for 230V)-

N° 1

N-26964

Hot-pressing device PM-1606

Summary of Contents for PM-1606
















































































Search results

Summary of Contents for PM-1606

Reviews:

Related manuals for PM-1606

Brands by name

Popular brands

Habasit PM-1606, General Manual Use And Maintenance

Search results

Summary of Contents for PM-1606

Reviews:

Related manuals for PM-1606

Brands by name

Popular brands