Habasit AF-61/8x30 Operating Instructions Manual Download

Page: 12 / 14

Operating instructions 4123

Appendix

Checklist preventive maintenance

Flexproof-Cutter AF-61/8x30

Page 12 of

Edition: 01/0206

Subject to alterations

4123INS.FAB-en0306ITA

Responsible persons:

A: Machine

Operator

Maintenance

Technician

Work to be carried out

Performance

Spares

number

(see operating instructions for further information and reference numbers)

periodically (monthly)

Evaluation criterion

Daily

Remarks

1. Cleaning

1.1

Clean the Flexproof-Cutter after use, remove residual matter

Inspection of the cutting pad

2.1

Check the condition of the cutting pad. If excessive wear and/or insufficient cutting quality
is found, the cutting pad has to be replaced.

Checking of die-cuts

3.1

Check quality of cuts and inspect cutting blades for damages. If necessary replace.
See operating instructions, Section 5.2

Remarks and notes:

Summary of Contents for AF-61/8x30















Search results

Summary of Contents for AF-61/8x30

Reviews:

Related manuals for AF-61/8x30

Brands by name

Popular brands

Habasit AF-61/8x30, Operating Instructions Manual

Search results

Summary of Contents for AF-61/8x30

Reviews:

Related manuals for AF-61/8x30

Brands by name

Popular brands