H3C WX Series Command Reference Manual Download Page 20

Page: 20 / 200

Default Level

2: System level

Parameters

None

Description

Use the

return

command to return to user view from current view, as you do with the

hot key

Ctrl+Z

Related commands:

quit

Examples

Return to user view from GigabitEthernet 1/0/1 view.

[Sysname-GigabitEthernet1/0/1] return

screen-length disable

Syntax

screen-length disable

undo screen-length disable

View

User view

Default Level

1: Monitor level

Parameters

None

Description

Use the

screen-length disable

command to disable the multiple-screen output function

of the current user.

Use the

undo screen-length disable

command to enable the multiple-screen output

function of the current user.

By default, a login user uses the settings of the

screen-length

command. The default

settings of the

screen-length

command are: multiple-screen output is enabled and 24

lines are displayed on the next screen. (For more information about the

screen-length

command, see

User Interface

in the

Fundamentals Command Reference

This command is applicable to the current user only and when a user re-logs in, the
settings restore to the system default.

Summary of Contents for WX Series









































































































































































































Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands

H3C WX Series, Command Reference Manual

Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands