51
[Sysname-nqa-admin-test] type dhcp
[Sysname-nqa-admin-test-dhcp] probe timeout 10000
# In HTTP template view, set the probe timeout time to 10000 milliseconds for the HTTP operation.
<Sysname> system-view
[Sysname] nqa template http httptplt
[Sysname-nqatplt-http-httptplt] probe timeout 10000
raw-request
Use
raw-request
to enter raw request view and specify the content of an HTTP or HTTPS
request.
Use
undo
raw-request
to restore the default.
Syntax
raw-request
undo
raw-request
Default
The contents of an HTTP or HTTPS raw request are not specified.
Views
HTTP operation view
HTTP/HTTPS template view
Predefined user roles
network-admin
Usage guidelines
This command places you in raw request view and deletes the previously configured request
content.
If the HTTP or HTTPS operation type is set to
raw
, you must enter raw request view and configure
the request content to be sent to the HTTP or HTTPS server. To ensure successful operations, make
sure the request content does not contain command aliases configured by using the
alias
command. For more information about the
alias
command, see CLI commands in
Fundamentals
Command Reference
.
Examples
# Enter raw request view and specify the content of a GET request for the HTTP operation.
<Sysname> system-view
[Sysname] nqa entry admin test
[Sysname-nqa-admin-test] type http
[Sysname-nqa-admin-test-http] raw-request
[Sysname-nqa-admin-test-http-raw-request] GET /sdn/ui/app/index HTTP/1.0\r\nHost:
172.0.0.2\r\n\r\n
# In HTTP template view, enter raw request view and specify the content of a POST request for the
HTTP operation.
<Sysname> system-view
[Sysname] nqa template http httptplt
[Sysname-nqatplt-http-httptplt] raw-request
[Sysname-nqatplt-http-httptplt-raw-request] POST /sdn/ui/app/index HTTP/1.0\r\nHost:
172.0.0.2\r\nAuthorization: Basic cm9vdDoxMjM0NTY=\r\n\r\n
Summary of Contents for SOHO IE4300
